Share information:
Fuel system (carburetor) of car Peugeot 106
.
Fuel/exhaust systems — carburettor petrol models — specifications
Fuel pump Type — Mechanical, driven by eccentric on camshaft Carburettor Type: 954 and 1124 cc models — Solex 32 PBISA16 1360 cc models: Engine code K2D — Solex 32-34 Z2 Engine code K5A — Solex 32-34 CISAC Designation:...
Fuel pump Type — Mechanical, driven by eccentric on camshaft Carburettor Type: 954 and 1124 cc models — Solex 32 PBISA16 1360 cc models: Engine code K2D — Solex 32-34 Z2 Engine code K5A — Solex 32-34 CISAC Designation:...
General information and precautions
The fuel system consists of a fuel tank mounted under the rear of the car, a mechanical fuel pump and a carburettor. The fuel pump is operated by an eccentric on the camshaft and is mounted on the rear of the cylinder...
The fuel system consists of a fuel tank mounted under the rear of the car, a mechanical fuel pump and a carburettor. The fuel pump is operated by an eccentric on the camshaft and is mounted on the rear of the cylinder...
Air cleaner assembly — removal and refitting
Removal 1. Slacken the retaining clips (where fitted) and disconnect the vacuum hose and breather hose from the front of the air cleaner housing-to-carburettor duct (see illustration). Where the crimped-type hose clips...
Removal 1. Slacken the retaining clips (where fitted) and disconnect the vacuum hose and breather hose from the front of the air cleaner housing-to-carburettor duct (see illustration). Where the crimped-type hose clips...
Air cleaner air temperature control system — information and component renewal
Information 1. The system is controlled by a heat-sensitive vacuum switch, mounted in the end of the air cleaner housing-to-carburettor duct. When the engine is started from cold, the switch is open, allowing inlet...
Information 1. The system is controlled by a heat-sensitive vacuum switch, mounted in the end of the air cleaner housing-to-carburettor duct. When the engine is started from cold, the switch is open, allowing inlet...
Fuel pump — testing, removal and refitting
Note: Refer to the warning note in Section 1 before proceeding. Testing 1. To test the fuel pump on the engine, disconnect the outlet pipe which leads to the carburettor. Hold a wad of rag by the pump outlet while an...
Note: Refer to the warning note in Section 1 before proceeding. Testing 1. To test the fuel pump on the engine, disconnect the outlet pipe which leads to the carburettor. Hold a wad of rag by the pump outlet while an...
Fuel gauge sender unit — removal and refitting
Note: Refer to the warning note in Section 1 before proceeding. Removal 1. Disconnect the battery negative terminal (refer to " Disconnecting the battery "). 2. For access to the sender unit, fold the rear seat cushion...
Note: Refer to the warning note in Section 1 before proceeding. Removal 1. Disconnect the battery negative terminal (refer to " Disconnecting the battery "). 2. For access to the sender unit, fold the rear seat cushion...
Fuel tank — removal and refitting
Note: Refer to the warning note in Section 1 before proceeding. Removal 1. Before removing the fuel tank, all fuel must be drained from the tank. Since a fuel tank drain plug Is not provided, it is therefore preferable...
Note: Refer to the warning note in Section 1 before proceeding. Removal 1. Before removing the fuel tank, all fuel must be drained from the tank. Since a fuel tank drain plug Is not provided, it is therefore preferable...
Accelerator cable — removal, refitting and adjustment
Removal 1. Where necessary, prise out the retaining clip and remove the plastic cover to gain access to the carburettor (see illustrations). 7.1a. Where necessary, prise out the retaining clip... 7.1b.... and remove the...
Removal 1. Where necessary, prise out the retaining clip and remove the plastic cover to gain access to the carburettor (see illustrations). 7.1a. Where necessary, prise out the retaining clip... 7.1b.... and remove the...
Accelerator pedal — removal and refitting
Removal 1. Undo the retaining nuts and remove the undercover panel from the driver's side of the facia. 2. Depress the retaining clips and detach the inner cable from the top of the accelerator pedal. 3. Slacken and...
Removal 1. Undo the retaining nuts and remove the undercover panel from the driver's side of the facia. 2. Depress the retaining clips and detach the inner cable from the top of the accelerator pedal. 3. Slacken and...
Choke cable — removal, refitting and adjustment
Removal 1. Where necessary, prise out the retaining clip and remove the plastic cover to gain access to the carburettor. 2. Free the choke inner cable from the carburettor linkage, then slacken and remove the retaining...
Removal 1. Where necessary, prise out the retaining clip and remove the plastic cover to gain access to the carburettor. 2. Free the choke inner cable from the carburettor linkage, then slacken and remove the retaining...
Unleaded petrol — general information and usage
Note: The information given in this Chapter is correct at the time of writing. If updated information is thought to be required, check with a Peugeot dealer. If travelling abroad, consult one of the motoring...
Note: The information given in this Chapter is correct at the time of writing. If updated information is thought to be required, check with a Peugeot dealer. If travelling abroad, consult one of the motoring...
Carburettor — general information
Solex 32 PBISA carburettor — 954 and 1124 cc models 1. The Soiex PBISA carburettor is a downdraught sing Ie-venturi instrument with a manually-controlled choke (see illustration). The carburettor consists of three main...
Solex 32 PBISA carburettor — 954 and 1124 cc models 1. The Soiex PBISA carburettor is a downdraught sing Ie-venturi instrument with a manually-controlled choke (see illustration). The carburettor consists of three main...
Carburettor — removal and refitting
Note: Refer to the warning note in Section 1 before proceeding. Removal 1. Disconnect the battery negative terminal (refer to " Disconnecting the battery "). 2. Remove the air cleaner-to-carburettor duct as described in...
Note: Refer to the warning note in Section 1 before proceeding. Removal 1. Disconnect the battery negative terminal (refer to " Disconnecting the battery "). 2. Remove the air cleaner-to-carburettor duct as described in...
Solex 32 PBISA carburettor — fault finding, overhaul and adjustments
Fault finding 1. If a carburettor fault is suspected, always check first that the ignition timing is correctly set, that the spark plugs are in good condition and correctly gapped, that the accelerator and choke cables...
Fault finding 1. If a carburettor fault is suspected, always check first that the ignition timing is correctly set, that the spark plugs are in good condition and correctly gapped, that the accelerator and choke cables...
Solex 32-34 Z2 and CISAC carburettor — fault finding, overhaul and adjustments
Fault finding 1. Refer to Section 13 . Overhaul Note: Refer to the warning note in Section 1 before proceeding. 2. Remove the carburettor from the vehicle as described in Section 12 . 3. Unscrew the idle cut-off...
Fault finding 1. Refer to Section 13 . Overhaul Note: Refer to the warning note in Section 1 before proceeding. 2. Remove the carburettor from the vehicle as described in Section 12 . 3. Unscrew the idle cut-off...
Inlet manifold — removal and refitting
Note: Refer to the warning note in Section 1 before proceeding. Removal 1. Remove the carburettor as described in Section 12 . 2. Drain the cooling system as described in Chapter 1A . 3. Undo the bolt securing the...
Note: Refer to the warning note in Section 1 before proceeding. Removal 1. Remove the carburettor as described in Section 12 . 2. Drain the cooling system as described in Chapter 1A . 3. Undo the bolt securing the...
Exhaust manifold — removal and refitting
Removal 1. Disconnect the hot-air intake hose from the manifold shroud and remove it from the vehicle (see illustration). 16.1. Remove the hot-air intake hose... 16.2. ... then undo the three retaining bolts (arrowed)...
Removal 1. Disconnect the hot-air intake hose from the manifold shroud and remove it from the vehicle (see illustration). 16.1. Remove the hot-air intake hose... 16.2. ... then undo the three retaining bolts (arrowed)...
Exhaust system — general information and component renewal
General information 1. On 954 and 1124 cc models, the exhaust system consists of two sections - the front pipe and a tailpipe. The front pipe is secured to the manifold by nuts and to the silencer by a clamping ring. 2....
General information 1. On 954 and 1124 cc models, the exhaust system consists of two sections - the front pipe and a tailpipe. The front pipe is secured to the manifold by nuts and to the silencer by a clamping ring. 2....
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link to this section in different formats
TEXTHTMLBB Code
- General information
- Introduction to manual
- Weekly checks
- Maintenance (petrol)
- Maintenance (diesel)
- Troubleshooting
- Power unit
- Petrol engines
- Diesel engines
- Engine overhaul
- Cooling and heating
- Fuel system (carburetor)
- Single point injection (petrol)
- Multipoint injection (petrol)
- Fuel system (diesel)
- Emission control system
- Engine electrical equipment
- Ignition system
- Diesel heating
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical diagrams