Share information:
Front wheel drive shafts of car Peugeot 106
.
Driveshafts — specifications
General Lubrication (overhaul only) — Use only special grease supplied in sachets with gaiter kits - joints are otherwise pre-packed with grease and sealed Torque wrench settings — Nm/lbf·ft Driveshaft intermediate...
General Lubrication (overhaul only) — Use only special grease supplied in sachets with gaiter kits - joints are otherwise pre-packed with grease and sealed Torque wrench settings — Nm/lbf·ft Driveshaft intermediate...
General information
Drive is transmitted from the differential to the front wheels by means of two soiid-steel driveshafts of unequal length (see illustration). 1.1. Typical driveshaft 1. Inner constant velocity joint; 2. Inner joint...
Drive is transmitted from the differential to the front wheels by means of two soiid-steel driveshafts of unequal length (see illustration). 1.1. Typical driveshaft 1. Inner constant velocity joint; 2. Inner joint...
Driveshafts — removal and refitting
Note: A balljoint separator tool will be required for this operation. A new driveshaft nut, a new track-rod end-to-steering arm nut and a new hub carrier-to-lower arm balljoint clamp nut, must be used on refitting....
Note: A balljoint separator tool will be required for this operation. A new driveshaft nut, a new track-rod end-to-steering arm nut and a new hub carrier-to-lower arm balljoint clamp nut, must be used on refitting....
Driveshaft rubber gaiters — renewal
Manual transmission models Outer joint 1. Remove the driveshaft as described in Section 2 . 2. Remove the inner constant velocity joint and gaiter as described in paragraphs 13 to 20. It is recommended that the inner...
Manual transmission models Outer joint 1. Remove the driveshaft as described in Section 2 . 2. Remove the inner constant velocity joint and gaiter as described in paragraphs 13 to 20. It is recommended that the inner...
Driveshaft overhaul — general information
If any of the checks described in Chapter 1A or 1B reveal wear in any driveshaft joint, first remove the roadwheel trim or centre cap (as appropriate). If the staking is still effective, the driveshaft nut should be...
If any of the checks described in Chapter 1A or 1B reveal wear in any driveshaft joint, first remove the roadwheel trim or centre cap (as appropriate). If the staking is still effective, the driveshaft nut should be...
Right-hand driveshaft intermediate bearing — renewal
Note: A suitable bearing puller will be required, to draw the bearing and collar off the driveshaft end. 1. Remove the right-hand driveshaft as described in Section 2 . 2. Check that the bearing outer race rotates...
Note: A suitable bearing puller will be required, to draw the bearing and collar off the driveshaft end. 1. Remove the right-hand driveshaft as described in Section 2 . 2. Check that the bearing outer race rotates...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See similar information for other Peugeot models
➨ Transmission: Drive shafts Peugeot 207 (2006-2014)
➨ Transmission: Drive shafts Peugeot 306 (1993-2002)
➨ Transmission: Drive shafts Peugeot 405 (1987-1997)
➨ Transmission: Drive shafts Peugeot Partner I (1996-2008)
Link to this section in different formats
TEXTHTMLBB Code
- General information
- Introduction to manual
- Weekly checks
- Maintenance (petrol)
- Maintenance (diesel)
- Troubleshooting
- Power unit
- Petrol engines
- Diesel engines
- Engine overhaul
- Cooling and heating
- Fuel system (carburetor)
- Single point injection (petrol)
- Multipoint injection (petrol)
- Fuel system (diesel)
- Emission control system
- Engine electrical equipment
- Ignition system
- Diesel heating
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical diagrams