Share information:
Car front suspension Peugeot 206
The front suspension of the Peugeot 206 car is independent spring, with a swinging telescopic shock absorber strut, on a wishbone, with a stabilizer bar.
Wheel alignment angles
Figure 7.1. Wheel alignment angles: A - longitudinal tilt of the wheel turn; B - camber angle; C - transverse tilt of the wheel pivot axis Checking the angles (figure 7.1) wheel installations should be carried out in...
Figure 7.1. Wheel alignment angles: A - longitudinal tilt of the wheel turn; B - camber angle; C - transverse tilt of the wheel pivot axis Checking the angles (figure 7.1) wheel installations should be carried out in...
Removal and installation the shock absorber strut
Remove the shock absorber strut in the following order: loosen the wheel mounting bolts; apply the parking brake to the car; raise the front of the vehicle and support it securely on stands; remove the wheel; Figure...
Remove the shock absorber strut in the following order: loosen the wheel mounting bolts; apply the parking brake to the car; raise the front of the vehicle and support it securely on stands; remove the wheel; Figure...
Transverse stability stabilizer
Figure 7.10. Installing the anti-roll bar: A, B - bald spots Stabilizer bar (figure 7.10) is attached to the car body with two brackets, into which rubber cushions are installed. For the correct installation of the...
Figure 7.10. Installing the anti-roll bar: A, B - bald spots Stabilizer bar (figure 7.10) is attached to the car body with two brackets, into which rubber cushions are installed. For the correct installation of the...
Removal and installation the steering knuckle
When removing and installing the steering knuckle, Peugeot service centers use the following special tool: hub locking device - 0606-AY; ball joint puller; ball joint release lever - 0622. Remove the steering knuckle in...
When removing and installing the steering knuckle, Peugeot service centers use the following special tool: hub locking device - 0606-AY; ball joint puller; ball joint release lever - 0622. Remove the steering knuckle in...
Removal and installation the lower suspension arm
Remove the lower arm in the following order: loosen the wheel mounting bolts; apply the parking brake to the car; raise the front of the vehicle and support it securely on stands; remove the wheel; Figure 7.12. Removing...
Remove the lower arm in the following order: loosen the wheel mounting bolts; apply the parking brake to the car; raise the front of the vehicle and support it securely on stands; remove the wheel; Figure 7.12. Removing...
Removal and installation of silent blocks
Press out the silent blocks in the following order: remove the lower arm as described above; install in the device and press out the middle silent block; Figure 7.13. Installing the silent block: 1 - silent block; 2 -...
Press out the silent blocks in the following order: remove the lower arm as described above; install in the device and press out the middle silent block; Figure 7.13. Installing the silent block: 1 - silent block; 2 -...
Removal and installation the front wheel hub bearing
Remove the front wheel hub bearing in the following order: remove the steering knuckle as described above; knock out the hub flange with a mandrel resting on the inside of the flange; if the inner bearing ring remains...
Remove the front wheel hub bearing in the following order: remove the steering knuckle as described above; knock out the hub flange with a mandrel resting on the inside of the flange; if the inner bearing ring remains...
Removal and installation the shock absorber spring
Remove the shock absorber spring in the following order: remove the shock absorber strut as described above; Figure 7.16. Removing the shock absorber spring: 1 - device; 2 - fork of the device; 3 - nut clamp fixture 1...
Remove the shock absorber spring in the following order: remove the shock absorber strut as described above; Figure 7.16. Removing the shock absorber spring: 1 - device; 2 - fork of the device; 3 - nut clamp fixture 1...
Adjusting the front wheel alignment
Figure 7.17. Adjusting the front wheel alignment: 1 - steering rod end; 2 - nut Only the front wheel alignment is adjusted on the vehicle. Adjust by rotating the tips 1 (figure 7.17) steering rods. One turn equals...
Figure 7.17. Adjusting the front wheel alignment: 1 - steering rod end; 2 - nut Only the front wheel alignment is adjusted on the vehicle. Adjust by rotating the tips 1 (figure 7.17) steering rods. One turn equals...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See similar information for other Peugeot models
➨ Chassis, running gear: Front suspension Peugeot 307 (2001-2008)
➨ Chassis, running gear: Front suspension Peugeot 405 (1987-1997)
Link to this section in different formats
TEXTHTMLBB Code
- General information
- Car care
- Governing bodies
- Driving and operation
- Power unit
- Engine characteristics
- Engine repair
- Cooling system
- Lubrication system
- Ignition system
- Control system (gasoline)
- Fuel system (gasoline)
- Control system (diesel)
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Car suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Headlights and lighting
- Power devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Gasoline engines
- Diesel engines
- Diesel power system
- Engine management system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Body elements
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits