Electrical equipment and devices of car Peugeot 207

Removal and installation steering column switches
Caution: When performing any work that involves disconnecting the steering wheel and wheels (steering wheel, steering column switch, steering column, steering rack, etc.) ensure that the steering column switch rotating...

Switching unit BSI 1
The switching unit (BSI 1) is the main unit in the electrical equipment system with multiplex communication. The unit includes a mechanical interface, an electronic board based on microcontrollers and a logical...

Diagnostic connector (C001)
Location The diagnostic connector (C001) (24) allows you to connect a diagnostic device (Lexia or Proxia) to the vehicle and communicate with all control units of the vehicle. The diagnostic connector has 16 connecting...

CAN IS Network
Location of the CAN IS network ECU The CAN IS network connects control units related to vehicle movement, such as the brake system, gearbox or engine. Data transfer rate 500 Kbps (High Speed). The CAN network is a...

CAN CAR Network
Location of the CAN CAR network ECU The CAN CAR network connects all safety nodes. Data transfer rate 125 Kbps (Low Speed). The transmission of information remains constant throughout the entire CAN CAR network....

CAN CONFORT network
Location of the CAN CONFORT network ECU The CAN CONFORT network is the interface between the driver and the vehicle systems. Data transfer rate 125 Kbps (Low Speed). Continuous transmission of information across the...

Diagnostics of body opening element control systems
Control of the vehicle's opening elements includes locking/unlocking the front and rear doors and the tailgate. Pin assignment of the 6-pin connector: 1 - "mass"; 2 - signal locked doors / child safety system...

Fault codes for the opening elements control system
Note: This chapter covers diagnostic trouble codes displayed by Lexia and Proxia equipment. * In the P-code function of each control unit, the variable "x" can take values "7", "8", "9", "A", "B", "C", "C", "E", "F".

Re-syncing the remote control
The procedure for synchronizing the high-frequency remote control is performed in case of replacement or adjustment of an additional remote control. 1. Turn off the ignition and remove the key. 2. Wait one minute...

Diagnostics of the rear view mirror control system
ECU connector for external rear view mirrors (18-pin, black) Block diagram of the rear view mirror control system

Diagnostics of the electric window control system
Driver's door window lift block diagram Passenger door window lifter block diagram Block diagram of rear window lifters Driver's side power window and mirror control panel connectors Black 6-pin electrical connector...

Rearview Mirror Control System Related Error Codes
Note: This chapter covers diagnostic trouble codes displayed by Lexia and Proxia equipment.

Power Window Control System Related Error Codes
Note: This chapter covers diagnostic trouble codes displayed by Lexia and Proxia equipment.

Diagnostics of the windshield wiper and washer control system
* Depending on the configuration. Block diagram of front windscreen wipers and washers Rear Windscreen Wiper and Washer Block Diagram * Depending on the configuration. Headlight Washer Block Diagram * Depending on the...

Instrument cluster diagnostics
26-pin instrument cluster connector (yellow): "v1" - chain 1; "v26" - chain 26. Error codes related to the operation of the instrument cluster Reading parameters Tests of actuators

Removal and installation the BSI 1 switching unit
Removal Turn off the ignition. Wait 3 minutes before disconnecting the battery. Disconnect the battery. Move the driver's seat back as far as possible. Remove the knee airbag (depending on the configuration). Open the...

Removal and installation the instrument cluster
Removal Turn off the ignition. Wait 3 minutes before disconnecting the battery. Disconnect the battery. Unlock the steering column, pull it out as far as possible and lower it. Detach the instrument panel visor (1) in...

Removal and installation the outside rearview mirror and side turn signal repeater
Remove the door trim panel (see section " Body "). Electrically adjustable rear view mirror Partially peel off the sealing sheet (in area "c"). Release the lock (1). Disconnect (depending on the configuration option):...

Disassembling the outside rearview mirror
Removal Note: Depending on the equipment option, an outside air temperature sensor may be installed in the outside mirror housing on the right side. Disconnect the turn signal repeater lamp (2) from the cover base (1)...

Removal and installation the front windshield wiper mechanism
Windscreen wiper arm puller 1335 Air intake grille Turn off the ignition. Take it off (on each side) front wiper shaft cover. Unscrew the nut (1). Using tool [1], remove the windscreen wiper arms (2). Move the seal (in...

Removal and installation the rear wiper mechanism
Removal Partially disassemble the tailgate (see section " Body "). Disconnect the cover (1) (in area "a"), unscrew the nut (2) and remove the cover. Remove the rear wiper arm (3). Tailgate with fixed glass. Disconnect...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

See similar information for other Peugeot models

➨ Electrical equipment: Equipment and devices Peugeot 106 (1991-2003)
➨ Electrical equipment: Equipment and devices Peugeot 305 (1977-1989)
➨ Electrical equipment: Equipment and devices Peugeot 405 (1987-1997)
➨ Electrical equipment: Equipment and devices Peugeot Partner I (1996-2008)

Link to this section in different formats

TEXTHTMLBB Code