Share information:
Front suspension of the car Peugeot 306
Front axle and front wheel suspension
The front suspension consists of two MacPherson struts with integrated shock absorbers located inside the coil springs. The lower end of each shock absorber strut is connected by a tie bolt to the upper part of the...
The front suspension consists of two MacPherson struts with integrated shock absorbers located inside the coil springs. The lower end of each shock absorber strut is connected by a tie bolt to the upper part of the...
Shock absorbers — removal, assembly and installation
11.1.1. Removal Before disassembling the shock absorber, the coil spring must be compressed. At Peugeot service stations, a special clamping device is used for this purpose, as shown in Figure 216. If such a device is...
11.1.1. Removal Before disassembling the shock absorber, the coil spring must be compressed. At Peugeot service stations, a special clamping device is used for this purpose, as shown in Figure 216. If such a device is...
Front wheel hubs and steering knuckles
11.2.1 Removal Although wheel bearings can be replaced with the steering knuckle installed, it is much easier to remove the steering knuckle and replace the bearings on a workbench. The wheel bearing must be replaced if...
11.2.1 Removal Although wheel bearings can be replaced with the steering knuckle installed, it is much easier to remove the steering knuckle and replace the bearings on a workbench. The wheel bearing must be replaced if...
Removal and installation the control arm
The wishbone can be removed without removing the complete shock absorber strut from the vehicle. Place the front of the car on stands and remove the wheel. Unscrew the tie bolt and nut from the bottom of the steering...
The wishbone can be removed without removing the complete shock absorber strut from the vehicle. Place the front of the car on stands and remove the wheel. Unscrew the tie bolt and nut from the bottom of the steering...
Removal and installation the anti-roll bar
Removing and installing the anti-roll bar on a Peugeot 306 is a labor-intensive job, as the entire frame must be removed from the underside of the body. In addition, it is necessary to disconnect the steering shaft from...
Removing and installing the anti-roll bar on a Peugeot 306 is a labor-intensive job, as the entire frame must be removed from the underside of the body. In addition, it is necessary to disconnect the steering shaft from...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See similar information for other Peugeot models
➨ Chassis, running gear: Front suspension Peugeot 206 (1998-2012)
➨ Chassis, running gear: Front suspension Peugeot 405 (1987-1997)
Link to this section in different formats
TEXTHTMLBB Code
- User manual
- Keys, doors and alarm
- Controls and instruments
- Driving and operation
- Maintenance
- Power unit
- Petrol engines TU3 and TU5
- Petrol engines EW10
- Diesel engines DV10
- Diesel engines DW10
- Transmission
- Clutch and drive shafts
- Mechanical gearbox
- Automatic gearbox
- Chassis, running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Power devices
- Airbags
- Electrical circuits
- General information
- Introduction to manual
- Specifications
- Gasoline engine
- Engine repair
- Lubrication system
- Cooling system
- Fuel injection
- Ignition system
- Diesel engine
- Engine repair
- Lubrication system
- Cooling system
- Fuel injection
- Transmission
- Clutch
- Gearbox
- Drive shafts
- Chassis, running gear
- Steering system
- Front suspension
- Rear suspension
- Brake system
- Electrical equipment
- Power devices
- Electrical circuits
- General information
- Maintenance
- Power unit
- Gasoline engines
- Diesel engines
- Cooling system (gasoline)
- Cooling system (diesel)
- Fuel system (gasoline)
- Fuel system (diesel)
- Ignition system
- Transmission
- Clutch
- Mechanical gearbox BB8
- Mechanical gearbox BE1
- Automatic gearbox ZF4
- Shafts, hubs and wheels
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Equipment and devices
- Headlights and lighting
- Power devices
- Electrical circuits
- Wiring diagrams (diesel)