Specifications and characteristics of car Peugeot J5

Gasoline engines — general technical data
Installed engines: 1.8 liter engine - 169 (XM7-T) 2.0L engine - 170V (XN1) or 170C (XN1-TA) Number and arrangement of cylinders - 4, in-line Valve arrangement - Overhung valves with two rocker shafts Camshaft - Cylinder...

Gasoline engines — manual
Cylinder head Material - Aluminum Cylinder head height: 92.5+0.15 mm Cylinder head height after surface milling: 92.10 mm The maximum permissible cylinder head tilt is 0.10 mm Gasket markings - Order by engine number...

1.9L Diesel Engine — D9B — General Technical Data
Engine displacement and type: diesel engine - XUD9A (D9B) Cylinder capacity: 1905 cm³ Number of cylinders - 4 The cylinders are arranged in-line Valve control - Camshaft, plate tappets Injection sequence: 1-3-4-2...

Diesel engine D9B — mechanics
Cylinder head Cylinder head height: 140.00±0.15 mm Minimum permissible cylinder head height is 139.55 mm The maximum permissible distortion of the cylinder head surface is 0.03 mm Milling of the cylinder head surface is...

Diesel and turbodiesel engine with a displacement of 2.5 liters
Engine displacement and types: Diesel engine - U25/651 Turbodiesel engine - U25/673 Working volume - 2.5 l Number of cylinders - 4 The cylinders are arranged in-line Position - Transverse position, with a forward tilt...

2.5L diesel and turbodiesel engine — manual
Cylinder head Cylinder head height: 117.00 + 0.5 mm Minimum permissible cylinder head height is 116.3 mm The maximum permissible distortion of the cylinder head surface is 0.10 mm Cylinder head surface milling -...

Engine lubrication system
Filling capacity: gasoline engines, without filter - 3.5 liters gasoline engines, dry engine - 4.0 liters diesel and turbodiesel engines with a displacement of 2.5 liters, manufactured before July 1986, without a filter...

Fuel system with carburetor
Carburetor: Installed types of carburetors: 169 V and 170 V engines - Solex PEU A 315 170 C engine - Solex PSA 425 Design - single-chamber carburetor Carburetor assembly PEU A315 PSA 425 Diffuser diameter 25 mm 25 mm...

Size and Adjustment Chart — clutch
Design - Single-plate dry clutch with diaphragm springs Installed clutch (examples): (it is necessary to order according to the list of spare parts) gasoline engines produced before July 1984 - 215 DBR 450 gasoline...

Transmission
Design - Four- or five-speed gearbox, in one housing with a drive gearbox Gearboxes have been improved several times with the introduction of new models. All gearboxes have a standard index and only a gearbox with the...

Steering system
Design - Rack and pinion steering mechanism Number of gear teeth: 5 Number of teeth on the rack: 25 Steering gear ratio: mechanical steering - 25.2:1 power steering - 16.0:1 Turning circle between the edges of the...

Front suspension
Design - Separate independent wheel suspension with MacPherson shock absorbers with built-in shock absorbers and coil springs, lower wishbones and reaction rods. Front springs Wire diameter: petrol engines, short...

Rear suspension
Construction. Two longitudinal leaf springs. Each spring has two main and two additional leaves. The exception is vehicles with soft suspension and camper vans. Fastening of spring leaves: front - spring pins and...

Brake system
Design: front disc brakes - Girling rear drum brakes - Girling with automatic brake shoe installation Handbrake - acts via a cable on the brakes of the rear wheels Equipment: Dual-circuit brake system with hydraulic...

Fuel injection device — diesel engine with a working volume of 2.5 liters
Lucas fuel injection system Installed on a diesel engine: produced from December 1983 to May 1987 - DPA pump, MA 300, N. R 3449 F 010 produced since May 1987 - DPA pump, MA 260, N. R 8443 111 A Installed on turbodiesel...

Fuel injection device — diesel engine with a working volume of 1.9 liters
Lucas fuel injection system Installed on a diesel engine: - XUD 9A/L engine D9B Until September 1990, the pump index was DPC 057, R 844 3B 380 A Since September 1990, the pump index is DPC 057, R 844 3B 383 B Static...

Injectors — size and adjustment charts
Manufacturer: Roto-Diesel or Bosch Injector inserts - Roto-Diesel: until September 1990 - RNDO SDC 6751 C since September 1990 - RNDO SDC 6751 E Injector inserts - Bosch: until April 1988 - DNSOSD 287 since April 1988 -...

Tightening torques — gasoline engines
Cylinder head bolts: Engine 169V up to number 012625 170V motor up to number 021874 170V engine with number 021875 first pass - 50 nm second pass - loosen third pass - 20 nm fourth pass - tightening at an angle of 90°...

Tightening Torques — 2.5l diesel and turbo diesel engines
Cylinder head: first pass - 40 nm second pass - tightening at an angle of 100° third pass - tightening at an angle of 100° tightening bolts - see main text Flywheel bolts - 90 Nm Main bearing bolts - 95 Nm Connecting...

Tightening Torques — 1.9l diesel engine
Cylinder head bolts: first pass - tighten to 70 Nm second pass - tighten to an angle of 180° Connecting rod bearing caps - 50 Nm Main bearing caps - 70 Nm Crankshaft belt pulley: first pass - 40 nm second pass - tighten...

Tightening torques — gearbox
Oil drain plug - standard gearbox (2 pieces) - 40 Nm Oil drain plug - all-wheel drive (3 pieces) - 40 Nm Oil filler plug - 13 nm Reverse light switch - 13 Nm Drive shaft nuts - 500 Nm Engine Flange Mounting Nuts -...

Tightening torques — steering
Steering wheel nut - 50 Nm Steering to chassis - 50 Nm Steering knuckle ends - 55 Nm Steering rods to the toothed rack - 60 Nm Tie rod end locknuts - 60 Nm Steering coupling tightening bolt - 25 Nm Steering knuckle arm...

Tightening torques — front suspension
See the picture. Shock absorber strut to body (1) - 20 Nm Piston rod nut (2) - 15 Nm Steering knuckle arm on steering knuckle (3) - 125 Nm Jet thrust (4) - 25 nm Jet thrust (5) - 140 nm Wishbone, inner mount (6) - 90 Nm...

Tightening torques — rear suspension
See the picture. Upper shock absorber mount (1) - 50 Nm Lower shock absorber mount (2) - 50 Nm Spring U-bolt nuts (3) — 80 Nm Spring shackle fastening, upper and lower (4) - 120 Nm Spring bracket (5) - 50 nm Spring...

Tightening torques — brake system
Brake caliper to steering knuckle - 142 Nm Brake caliper to mounting - 34 Nm Brake discs to wheel hubs - 15 nm Brake master cylinder to power steering - 20 Nm Power steering to bulkhead - 20 Nm Air release valves - 8 Nm...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

See similar information for other Peugeot models

➨ General information: Specifications Peugeot 306 (1993-2002)

Link to this section in different formats

TEXTHTMLBB Code

Partner I (1996-2008)