Engine cooling and vehicle heating Peugeot 605

General information
The cooling system includes a water pump, radiator, radiator fan, expansion tank, thermostat, heater radiator, connecting hoses and sensors. The circulation of the coolant is controlled by a thermostat. Until the engine...

Water Pump — Removal
1. Drain the coolant. 2. Remove the timing belt of the gas distribution mechanism drive (see the relevant chapter). XU series petrol engine vehicles 3. Unscrew the mounting bolts and remove the water pump 1, remove the...

Water pump — installation
The water pump is installed in the reverse order of removal, taking into account the following: XU series petrol engine vehicles 18. Clean the sealing surface of the pump. 19. Install the water pump with a new sealing...

Radiator — removal and installation
Attention! Cars with diesel engine DKSATE since 1998 are equipped with two radiators (see illustration 3.0). Attention! The procedure is given using the example of cars with a petrol engine ES9J4. 1. Drain the coolant....

Transmission Oil Cooler Radiator — Removal
Attention. The procedure is given using the example of cars with automatic transmission. 4.0 Unscrew the two bolts 4 securing the radiator 3 for cooling the transmission oil, remove the spacer washers 6 1. Remove the...

Transmission Oil Cooling Radiator — Installation
The transmission oil cooling radiator is installed in the reverse order of removal, taking into account the following. 7. All seals and washers must be replaced. 8. Install the transmission oil cooling radiator into its...

Heater — removal and installation
1. Remove the instrument panel. 2. Unscrew bolts 1, and then remove bracket 2 (see illustration). 5.2 Unscrew bolts 1 and then remove bracket 2 3. Unscrew bolts 3 and move spacer 4 away from the work area (see arrow in...

Heater Fan — Removal and Installation
1. Turn the locks 1 a quarter turn (see illustration) and remove the trim under the instrument panel. 6.1 Turn the locks 1 a quarter turn 2. Disconnect the wiring harnesses and plug from the fan (see illustration). 6.2...

Thermostat — removal and installation
Attention! The procedure is given using the example of cars with a petrol engine ES9J4. 1. Disconnect the coolant sensor connector 1, then remove the air filter and air outlet duct 2 (see illustration). 7.1 Disconnect...

Outside Air Temperature Sensor — Removal and Installation
1. Unscrew bolts 1,2, remove cover 3 of the windshield washer reservoir, and then remove grille 4 of the fairing (see illustration). 8.1 Unscrew bolts 1, 2, remove cover 3 of the windshield washer reservoir, and then...

Coolant Temperature Sensor — Removal and Installation
1. Turn the fasteners 1 a quarter turn and remove the trim under the instrument panel (see illustration). 9.1 Turn the fasteners 1 a quarter turn and remove the trim under the instrument panel 2. Remove coolant...

Cooling system — bleeding
At the manufacturer's plant, an aqueous solution of antifreeze is poured into the cooling system. Antifreeze is a concentrated ethylene glycol with anti-corrosion additives that prevents freezing and corrosion of the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

See similar information for other Peugeot models

➨ Power unit: Cooling and heating Peugeot 106 (1991-2003)
➨ Power unit: Cooling system Peugeot 207 (2006-2014)
➨ Gasoline engine: Cooling system Peugeot 306 (1993-2002)
➨ Power unit: Cooling and lubrication system Peugeot 405 (1987-1997)
➨ Gasoline engine: Cooling system Peugeot J5 (1981-1993)

Link to this section in different formats

TEXTHTMLBB Code