Car automatic transmission Peugeot 605

Automatic Transmission Specifications
Automatic Transmission Specifications

General information about automatic transmission
The Peugeot 605 is equipped with a four-speed automatic transmission (see illustration 1.0), the main elements of which are the torque converter and the electronic control unit of the gearbox. The electronic unit...

Transmission Oil — Checking Level
The 4HP20 automatic transmission (AG) does not require replacement of transmission oil during the entire service life. The transmission oil level must be checked every 60,000 km. Automatic transmission with a dipstick....

Transmission oil — replacement
Automatic transmission with dipstick 16. Unscrew the plug 1 of the drain hole (see illustration) and drain the transmission oil into a suitable container. It is impossible to drain the oil from the torque converter...

Torque Converter — Removal
1. Remove the gearbox (see the relevant chapter). 2. Install special handles for removing/installing the torque converter. Select the handles depending on the type of torque converter fastening: if the torque converter...

Torque converter — installation
6. Clean the seal seat. 7. Pack the new torque converter seal with a suitable mandrel "c" (see illustration). 3.7 Fit the new torque converter seal using a suitable mandrel "c" 8. Check the condition of the torque...

Modulator — removal
1. Remove the air filter. 2. Remove the battery and its tray, as well as the bracket that holds it. 3. Disconnect plug 1 (see illustration). 4.3 Disconnect plug 1 4. Drain the transmission oil. 5. Release hose 2 from...

Modulator — installation
The modulator is installed in the reverse order of removal, taking into account the following. 13. The tightening torque of the output shaft speed sensor is 10 Nm. 14. Make sure the rod is properly seated in the...

Speedometer sensor — removal and installation
1. Remove the heat shield. 2. Disconnect the plug 3. Unscrew the bolt 4, then carefully turn the speedometer sensor 2 (see arrow A in the illustration), to loosen its fit. 5.2 Disconnect plug 3, unscrew bolt 4, then...

Gear shift mechanism — removal and installation
1. Set the gearshift lever to position "P". 2. Remove the 1 pocket cover by pressing the locking tabs (see illustration). 6.2 Remove the 1 pocket cover by pressing the locking tabs 3. Unscrew the bolts 2 (see...

Gear shift mechanism — adjustment
24. Set the gearshift lever to position "P". 25. Turn on the ignition. 26. Make sure that the gearshift lever position indicator on the panel matches the position of the lever. 27. Run the starter for a while. 28. Set...

Gearshift box-removal
Note: There is no need to drain the transmission oil to remove the automatic transmission. 1. Jack up the car and place it on jack stands. 2. Remove the air filter 1 (see illustration). 7.2 Remove the air filter 1 3....

Gearbox — installation
25. Install a new sealing ring 33 of the torque converter (see illustration). 7.25 Install new sealing ring 33 of the torque converter 26. Install the torque converter so that the fastening A is facing downwards (see...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

See similar information for other Peugeot models

➨ Transmission: Automatic gearbox Peugeot 106 (1991-2003)
➨ Transmission: Automatic gearbox Peugeot 206 (1998-2012)
➨ Transmission: Automatic gearbox Peugeot 307 (2001-2008)
➨ Transmission: Automatic gearbox Peugeot 406 (1995-2004)
➨ Transmission: Automatic gearbox Peugeot 807 (2002-2014)

Link to this section in different formats

TEXTHTMLBB Code