Power electrical devices of the car Peugeot 605

Electrical System — General Description and Precautions
When checking electrical equipment, a motorist, referring to technical documentation, constantly encounters such concepts as voltage, current, resistance. Voltage is measured in volts (V), current in amperes (A), and...

Measuring instruments
To perform the measurements required for servicing cars, so-called combined control and measuring devices are available for sale. They combine a voltmeter for measuring voltage, an ammeter for measuring current, and an...

Voltage measurement
The presence or absence of voltage can be checked with a simple test light or tester. Of course, this can only check the voltage when it is present. To check the magnitude of the voltage present, a voltmeter is needed....

Measuring current
It is comparatively rare to need to measure current strength. For this, an ammeter is needed, which can also be a component of combined control and measuring devices. Before measuring the current strength, the...

Measuring resistance
Before taking measurements, you must make sure that the contacts to which the ohmmeter is connected are not under voltage. This means that you should always disconnect the battery first. Otherwise, you may damage the...

Troubleshooting electrical equipment
When troubleshooting an electrical installation, a systematic approach is important. This applies to both checking a failed light bulb and finding the cause of an electric motor stopping. The first step should always be...

Battery capacity — check
Checking the density of the electrolyte The degree of electrolyte density in combination with voltage measurement data allows us to draw conclusions about the condition of the battery. To check, you need a hydrometer,...

Starter — removal and installation
PEUGEOT 605 vehicles are equipped with Valeo, Bosch or Mitsubishi starters (see illustrations 3.0, 3.0a and 3.0b). 3.0 Valeo Starter 1 - traction relay 2 - gear engagement lever 3 - overrunning clutch 4 - coupling shaft...

Generator — device
PEUGEOT 605 is equipped with a Valeo, Bosch or Mitsubishi generator (see illustrations 4.0, 4.0a and 4.0b). 4.0 Bosch Generator 1 - rotor 2 - stator 3 - diode board 4 - front bearing 5 - rear bearing 6 - voltage...

Generator — check
The battery charge indicator light should not light while driving. If it does, there is a fault with the alternator or voltage regulator. As a first step, check the wiring at the alternator terminals. 1. Make sure the...

Generator — removal
4. Disconnect the battery. 5. Remove the alternator drive belt, see the relevant chapter. 6. Unscrew the mounting bolts and remove the power steering pump pulley (see illustration). 4.6 Unscrew the mounting bolts and...

Headlights — removal and installation
Headlights Removal 1. Open the hood and disconnect the negative (-) battery cable terminal. 2. Unscrew the bolts 1 and remove the logo A by pressing it with a flat screwdriver (see illustration). 5.2 Unscrew the bolts 1...

Windscreen wiper — removal and installation
After about six months of use, the rubber band of the windshield wiper blade wears out and does not always provide sufficient cleaning of the glass. In this case, there are two options for replacing the brushes. You can...

Battery tray — removal and installation
Removal 1. Disconnect the battery cable terminals, remove the air filter, and then the battery. 2. Move the air conditioner refrigerant tank 1 to the side without opening the circulation circuit (see illustration). 7.2...

Instrument cluster — removal and installation
When purchasing a used car, you should check the functioning of the indicators and warning lights on the instrument panel. 1. Disconnect the negative (-) battery terminal. 2. Disconnect the speedometer cable 2 together...

Ignition System — General Information and Precautions
The ignition system ensures the timely formation of a spark discharge necessary for the ignition of the air-fuel mixture supplied to the combustion chambers of the cylinders of gasoline engines. To form a spark...

Spark plugs — general information
A spark plug consists of a central electrode, an insulator with a housing, and one or more electrodes. An ignition spark jumps between the central electrode and the side electrode(s), igniting the fuel-air mixture....

Spark plugs — removal
Attention! The procedure is given using the example of cars with a petrol engine ES9J4. 1. Remove the intake manifold. 2. Disconnect the ignition coil unit power plug. 3. Remove block 1 of ignition coils by prying it...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

See similar information for other Peugeot models

➨ Electrical equipment: Power devices Peugeot 207 (2006-2014)
➨ Electrical equipment: Power devices Peugeot 305 (1977-1989)
➨ Electrical equipment: Power devices Peugeot J5 (1981-1993)

Link to this section in different formats

TEXTHTMLBB Code