Table of contents: Front brakes 🠇 Rear brakes 🠇 Vacuum booster 🠇 Master brake cylinder 🠇 4x4 vehicles 🠇 Classic braking system 🠇 Braking system with ABS 🠇 Control pressure (MPa) for hydraulic…🠇 Control pressure (MPa) for hydraulic…🠇 Tightening moments 🠇
Front brakes
| Front brakes | disc, with single-piston floating calipers |
| Support: | |
| - brand | Bendix IV |
| – piston diameter | 48 mm |
| – brake discs: | |
| • o.D | 266 mm |
| • nominal thickness | 10 mm |
| • minimum thickness | 9 mm (grinding up to 0.5 mm per side) |
| • maximum runout | 0.07 mm |
| - brake pads | |
| • type of pads | Abex 903 or Valeo F599 |
| • minimum thickness | determined by erasing the intermediate control groove |
| • friction surface of one lining | 35 cm² |
Rear brakes
| Rear brakes | drum, type HCSF, with automatic adjustment of the clearance of the pads |
| Brand | Bendix |
| Brake drums: | |
| – nominal working diameter | 228.6 mm |
| – working diameter after regrinding | 229.6 mm |
| Brake pads: | |
| - type | Valeo F 154 |
| - width | 40 mm |
| Brake cylinder (with built-in pressure regulator): | |
| - diameter | 20.6 mm |
Vacuum booster
| Type | Isovac |
| Brand | Bendix or ATE |
| Diameter | 203.2 mm |
Master brake cylinder
| Type | dual-circuit |
| Brand | Bendix or ATE |
| Diameter | 20.6 mm |
4x4 vehicles
All 4x4 vehicles are equipped with ventilated disc front brakes and disc rear brakes (with full disks). These vehicles may also be equipped with an anti-lock braking system (ABS).
| Front brakes: | |
| - calipers | Girling Colette 14 CJ/PE |
| – piston diameter | 54 mm |
| – disks: | |
| • o.D | 266 mm |
| • nominal thickness | 20.4 mm |
| • minimum thickness | 18 mm |
| • maximum warpage | 0.07 mm |
| Rear brakes: | |
| - calipers | Girling C 36 HL PE |
| – piston diameter | 36 mm |
| – disks: | |
| • o.D | 249 mm |
| • nominal thickness | 10 mm |
| • minimum thickness | 9 mm |
| • maximum warpage | 0.07 mm |
Classic braking system
| Vacuum booster | type Isovac |
| Diameter | 228.6 mm |
| Master brake cylinder | dual circuit, Bendix or Ate |
| Piston diameter | 20.6 mm |
Braking system with ABS
| Sensors: | |
| - brand | Bendix |
| – resistance at 20°C | 1000 – 1400 Ohm |
| - air gap (distance between sensor and gear) | 0.5 mm |
| - pressure regulator | the functioning of the regulator depends on the load on the vehicle |
Control pressure (MPa) for hydraulic pressure 7.0 MPa
Before | 0,8 | 6,0 | 10,0 |
Back | 0,8 | 2,5 | 3,7 |
Control pressure (MPa) for hydraulic pressure 9.0 MPa
Before | 2,5 | 6,0 | 10,0 |
Back | 2,5 | 3,9 | 5,1 |
Tightening moments
| Front Brake Caliper Mount (Bendix) | 120 Nm |
| Wheel mounting bolts | 85 Nm |
(Original can be viewed at: www.PEUGEOTBOOK.ru)