Car rear suspension Peugeot 405

Rear suspension — design description
Rear suspension components and rear wheel hubs 1 - beam; 2 – suspension arm; 3 – beam axis; 4 – buffer; 5 – torsion bar; 6 – stabilizer; 7 – hub; 8 – hub nut; 9 – safety gasket; 10 – dust cover; 11 – nut cover; 12 –...

Rear suspension specifications
Torsion bars Diameter 18.6 mm Elasticity (on the wheel) 63 mm/ 1000 N Full bend (on wheel) 257.6 mm Repair size for installing a new torsion bar 393 mm Stabilizer Diameter: 18 mm. Location: in front of suspension arms....

Replacing the rear shock absorber
Attention! When removing and installing the rear suspension shock absorbers, the car must stand on its wheels. Installing the shock absorber 1 – shock absorber, 2 – crossbar mount, 3 – lever mount X = 328 mm – distance...

Replacing rear torsion bars
Torsion bar mount on the lever 1 – lever, 2 – torsion bar mounting bolt, 3 – eccentric locking pad, 4 – stabilizer mounting bolt, 5 – stabilizer end mounting bolt, 6 – support pad Removal 1. Place the car on a lift and...

Stabilizer — removal and installation
Removal 1. Place the car on stands and remove the wheels. 2. Unscrew the mounting bolts and remove the gaskets. 3. Loosen the stabilizer flange bolts on the arm, unscrew the right bolt (depending on the decision). 4....

Rear suspension arm — removal and installation
Removal 1. Raise the rear of the vehicle and remove the wheels. 2. Remove the shock absorber from the corresponding side. 3. Remove the stabilizer and torsion bar. 4. Disconnect the brake line at the brake line mounting...

Removal and installation the rear suspension
Caution! The rear suspension is attached to the body with Torx bolts. A long #50 Torx bit is required to remove the rear suspension. Rear suspension unit Removal the rear suspension unit 1 – filler pipe, 2 – tank mount,...

Adjusting the height of the body suspension
Measurement 1. Check the tire pressure. 2. Equipped car (without load, with full fuel tank) install on a flat and horizontal surface. 3. Measure the distance between the base and the bottom of the body in front of the...

Rear wheel hubs — removal and installation
Removal 1. Raise the vehicle and remove the wheel on the appropriate side. 2. Remove the brake drum or brake disc. 3. If present, remove the ABS sensor. 4. Using a lever, remove the protective cap from the central part...

Features of the rear suspension of 4x4 vehicles
Rear suspension elements (4 x 4 powertrain) 1 – rear suspension cross member, 2 – body mount support, 3 – metal-rubber element, 4 – suspension buffer, 5 – suspension arm, 6 – hub base, 7 – hub, 8 – axle shaft nut, 9 –...

Replacement of the tank
1. Install the vehicle on a stationary lift. 2. Remove the left trunk trim. 3. Disconnect the hydraulic pump power supply connector (red) (wires M326 and 326). 4. Connect the free terminals of the connector next to the...

Removal and installation the suspension arm
Rear suspension and rear axle N – oil level plug, V – oil drain plug 1 – rear axle bracket, 2 – suspension cylinder, 3 – reservoir, 4 – heat shield Installing the rear suspension arm axle 1 – axle, 2 – lever, 3 – tube,...

Removal and installation the suspension cylinder
Installing the suspension cylinder 1 – high pressure connection, 2 – connection bolt, 3 – piston axis latch on suspension arm, 4 – cylinder casing, 5, 6 – oil recirculation lines Suspension cylinder fasteners 11 –...

Bleeding air from the hydraulic circuit
Pressure regulator 1 – suspension high pressure connection, 2 – high pressure circuit deaerator, 3 – brake system connection Elements of hydropneumatic rear suspension (4x4 powertrain) 1 – LHM fluid reservoir, 2 –...

Removal and installation the pump
Installing electrical cable clamps on a high pressure pump 1 – pump, 2 – electrically controlled valve, 3 – electrical wires, 4 – clamps 1. Install the vehicle on a stationary lift. 2. Remove the left trunk trim. 3....

Removal and installation the hub
1. Raise the appropriate side of the vehicle. 2. Remove the wheel, remove the cotter pin and the locking element of the drive axle nut. 3. Secure the hub with a lever (it is recommended to use the 6310 T device) and...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

See similar information for other Peugeot models

➨ Chassis, running gear: Rear suspension Peugeot 206 (1998-2012)
➨ Chassis, running gear: Rear suspension Peugeot 306 (1993-2002)

Link to this section in different formats

TEXTHTMLBB Code