Share information:
Car rear suspension Peugeot 206
General information about the rear suspension
The rear suspension of the Peugeot 206 is independent, lever, with a tubular cross beam. The elastic element of the suspension is the torsion bars, on which the longitudinal levers are mounted. Tightening torques, Nm...
The rear suspension of the Peugeot 206 is independent, lever, with a tubular cross beam. The elastic element of the suspension is the torsion bars, on which the longitudinal levers are mounted. Tightening torques, Nm...
Removal and installation the rear suspension beam assembly
Remove the rear suspension beam in the following order: place the car on a lift; remove the parking brake console from underneath the vehicle; disconnect the parking brake cables; remove the spare tire; remove the...
Remove the rear suspension beam in the following order: place the car on a lift; remove the parking brake console from underneath the vehicle; disconnect the parking brake cables; remove the spare tire; remove the...
Removal and installation the anti-roll bar
Remove the rear suspension stabilizer bar in the following order: remove the wheel from the right side; Figure 7.20. Right side of the rear suspension: 1 - washer; 2 - bolt; 3 - cork unscrew bolt 2 (figure 7.20); remove...
Remove the rear suspension stabilizer bar in the following order: remove the wheel from the right side; Figure 7.20. Right side of the rear suspension: 1 - washer; 2 - bolt; 3 - cork unscrew bolt 2 (figure 7.20); remove...
Removal and installation the rear shock absorber
When removing and installing the rear shock absorber, Peugeot service centers use the 0916-A tool to compress the suspension. Remove the rear shock absorber in the following order: Figure 7.26. Removing the rear shock...
When removing and installing the rear shock absorber, Peugeot service centers use the 0916-A tool to compress the suspension. Remove the rear shock absorber in the following order: Figure 7.26. Removing the rear shock...
Removal and installation rear suspension torsion bars
When removing and installing torsion bars, Peugeot service centers use the following special tool: inertial puller 0316-A; shock absorber imitation device; key head 0539-C. Remove the torsion bars in the following...
When removing and installing torsion bars, Peugeot service centers use the following special tool: inertial puller 0316-A; shock absorber imitation device; key head 0539-C. Remove the torsion bars in the following...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See similar information for other Peugeot models
➨ Chassis, running gear: Rear suspension Peugeot 307 (2001-2008)
➨ Chassis, running gear: Rear suspension Peugeot 405 (1987-1997)
Link to this section in different formats
TEXTHTMLBB Code
- General information
- Car care
- Governing bodies
- Driving and operation
- Power unit
- Engine characteristics
- Engine repair
- Cooling system
- Lubrication system
- Ignition system
- Control system (gasoline)
- Fuel system (gasoline)
- Control system (diesel)
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Car suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Headlights and lighting
- Power devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Gasoline engines
- Diesel engines
- Diesel power system
- Engine management system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Body elements
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits