Body — general information The body is made of sheet steel, the assembly is carried out by spot and glue welding (back floor). Gain Details (spars) made of thick sheet steel (2 to 2.5 mm). Body sheet steel pre-treated, galvanized or 95%...
Doors — general information The doors have aluminum side reinforcements and stiffeners. The hinges are adjusted by screws on the door and on the body. The lock cylinders are removable - this requires removing the inner decorative panel of the...
Glazing — general information Designed with an athermal windshield (pasted). Movable and fixed glass doors and openings can be laminated or tempered (on some versions). The rear window is available in two versions: tinted or non-tinted, with an...
Replacing the front fender liner Special fixture: 1 - trim remover 1350-ZZ. Place the car on a lift. Remove the front wheels. Detach the clips (3) using the device [1]. Loosen the screws (2) and remove the front fender (1). Install the parts in reverse...
Threshold replacement Place the car on a lift. Loosen the sill (1) (in the zone «A») and remove. Install the parts in reverse order. Note. When installing, check the condition of the latches, replace if necessary.
Front bumper replacement Place the car on a lift. Remove the front fenders. Open the hood. Loosen the top screws (1). Loosen the two bottom screws (2). Disconnect connector (3) (Right side) and fog lamp connector (left-hand side). Disconnect...
Disassembly and assembly of the front bumper Special fixtures: 1 - spatula 1350; 2 - spatula 1327. Remove the front bumper. Headlight washer Remove the assembly of jets and a decorative element of the headlight washer (from each side). Release from fasteners (1)...
Hood replacement Open the hood. Disconnect the windshield washer tube retainer (1). Disconnect the washer pipe at the connection point (in the zone «A»). Loosen the nuts (2) and remove the hood (3). Bonnet Hinge Lever Remove the air...
Bonnet lock actuator replacement Hood lock Turn away bolts (1). Move the lock (2). Disconnect the hood release cable (3) (in the zone «A»). Remove the lock (2). Hood lock cable Note. To disconnect the cable on the lock, it must be removed. Switch off...
Front fender replacement Front fender Remove the front bumper, headlights and air intake grille (see section « electrical equipment »). Detach the mount (1) and remove the soundproofing seal (2). Note. Break off the rivet pins before drilling....
Rear bumper replacement (3- and 5-door hatchback) Place the car on a lift. Remove rear wheels. Remove the clips (1) (with a thin screwdriver). Release partially the rear fender liner (from each side). Loosen the fixing screws (2) bumper (3). Disconnect connector (4)...
Replacing the rear bumper (station wagon) Place the car on a lift. Loosen the fixing screws (1) and remove the brackets (2) using a thin screwdriver. Loosen the rear bumper (3) (in zones «A» And «b») (operation is performed symmetrically). Detach the clips (4)....
Disassembly and assembly of the rear bumper (3- and 5-door hatchback) Remove the rear bumper. Disconnect connectors (1) parking aid sensors (2). Release from clamps (in the zone «A») with a thin screwdriver. Remove the parking aid sensors (2). Remove the wiring harness (3) from supports...
Disassembly and assembly of the rear bumper (station wagon) Remove the rear bumper. Disconnect the connector in the area «A». Release the parking aid sensor (1) (in the zone «b») using a thin screwdriver and remove. Note. Carry out similar operations with other sensors of the...
Tailgate replacement (3- and 5-door hatchback) Remove the tailgate wiring harness from the inside (see below). Remove the handles (1). Special fixture: 1 - key for removing the tailgate 1368. Remove fasteners (2). Remove the rear trim panels (3) (see below). Move...
Replacing the tailgate (station wagon) Remove the additional brake light (see section « electrical equipment »). Partially disassemble the tailgate (see below). Move the wiring harness aside. Block the lock. Disconnect shock absorbers (2) tailgate (1). Turn...
Replacement of a bracket of the lock of a door of a back Remove the trunk seal (lower part). Remove the trunk sill trim (see below). Turn away bolts (1) and remove the lock (2). Install the parts in reverse order. Adjustment Note. To adjust the lock bracket, remove the guides...
Disassembly and assembly of the tailgate (3- and 5-door hatchback) Disconnect the battery. Remove: additional brake light; wiper blade; register sign. Detach trim panels (1) tailgate pillars (in the zone «A»). Remove trim panels (1). Disconnect the tailgate trim panels (2) (in the zone...
Disassembly and assembly of the tailgate (station wagon) Open the tailgate. Lock the trunk lid lock. Perform the following operations: turn off the ignition; wait at least 3 minutes before disconnecting the battery; disconnect the battery. Loose decorative trims (1) And (2)...
Front door replacement Install the support [1] under the front door (1). Turn away bolts (2). Slide the front door (1) in the direction of the arrow «A». Move the door wiring harness cover (3). Disconnect connectors (4). Remove front door...
Rear door replacement Install the support [1] under the rear door (1). Turn away bolts (2). push back the door (1) in the direction of the arrow «A». Move the door wiring harness cover (3). Disconnect connector (4). Remove the door (1)....
Body clearances: 3-door hatchback Attention. The values of gaps and overlaps are given for information. When adjusting, first of all, it is necessary to ensure the same gaps for each element and check the overlaps on each element.
Body clearances: 5-door hatchback Attention. The values of gaps and overlaps are given for information. When adjusting, first of all, it is necessary to ensure the same gaps for each element and check the overlaps on each element.