Share information:
Car steering Peugeot 206
General information about steering
Peugeot cars use rack-and-pinion steering with two cardan shafts. A hydraulic booster option is available. Tightening torques, Nm Steering gear mounting studs 10 Nuts 80 Bolts for clamps of liquid supply and discharge...
Peugeot cars use rack-and-pinion steering with two cardan shafts. A hydraulic booster option is available. Tightening torques, Nm Steering gear mounting studs 10 Nuts 80 Bolts for clamps of liquid supply and discharge...
Removal and installation the steering gear
When removing and installing the steering gear, Peugeot service centers use the following special tool: ball joint puller - 0709; ball joint removal tool - 0216-G2. Remove the steering gear in the following order: raise...
When removing and installing the steering gear, Peugeot service centers use the following special tool: ball joint puller - 0709; ball joint removal tool - 0216-G2. Remove the steering gear in the following order: raise...
Removal and installation the steering column
Remove the steering column in the following order: Figure 8.1. Disconnecting the steering cardan shaft: 1 - bolt; 2 - gasket; 3 - steering wheel shaft unscrew bolt 1 (see figure 8.1); disable the integrated airbag and...
Remove the steering column in the following order: Figure 8.1. Disconnecting the steering cardan shaft: 1 - bolt; 2 - gasket; 3 - steering wheel shaft unscrew bolt 1 (see figure 8.1); disable the integrated airbag and...
Removal and installation the toothed rack support
Remove the toothed rack support in the following order: remove the steering gear; Caution: To prevent dirt from entering the power steering circuit, close the two holes in the distribution valve and in the two power...
Remove the toothed rack support in the following order: remove the steering gear; Caution: To prevent dirt from entering the power steering circuit, close the two holes in the distribution valve and in the two power...
Removal and installation the mudguard
When removing and installing the mudguard, Peugeot service centres use the following special tool: ball joint puller - 0709; clamp for clamps - type clic 0172-Z. Remove the mudguard in the following order: remove the...
When removing and installing the mudguard, Peugeot service centres use the following special tool: ball joint puller - 0709; clamp for clamps - type clic 0172-Z. Remove the mudguard in the following order: remove the...
Removal and installation the ignition switch
Remove the ignition switch in the following order: disconnect the negative battery cable; remove the upper and lower steering column covers; remove the lower instrument panel trim; disconnect the contact connectors;...
Remove the ignition switch in the following order: disconnect the negative battery cable; remove the upper and lower steering column covers; remove the lower instrument panel trim; disconnect the contact connectors;...
Removal and installation the distribution valve
When removing and installing the distribution valve, Peugeot service centers use the following special tool: installation mandrel 0720-D; inertial puller 0316-A; hex head 0720-G. Remove the distribution valve in the...
When removing and installing the distribution valve, Peugeot service centers use the following special tool: installation mandrel 0720-D; inertial puller 0316-A; hex head 0720-G. Remove the distribution valve in the...
Draining and filling the hydraulic circuit of the power steering
Caution! Take measures to prevent even the smallest contaminants from entering the system. Use only fresh working fluid to top up and fill the system. Drain the working fluid in the following order: stop the engine and...
Caution! Take measures to prevent even the smallest contaminants from entering the system. Use only fresh working fluid to top up and fill the system. Drain the working fluid in the following order: stop the engine and...
Control and adjustment of the steering mechanism
Check the steering gear clearance in the following order: 1) Clamp the steering gear in a vice with soft pads; Figure 8.36. Removing the mudguard: 1 - mudguard; 2, 3 - clamps 2) remove clamps 2 and 3 (figure 8.36); 3)...
Check the steering gear clearance in the following order: 1) Clamp the steering gear in a vice with soft pads; Figure 8.36. Removing the mudguard: 1 - mudguard; 2, 3 - clamps 2) remove clamps 2 and 3 (figure 8.36); 3)...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See similar information for other Peugeot models
➨ Chassis, running gear: Steering Peugeot 106 (1991-2003)
➨ Chassis, running gear: Steering Peugeot 305 (1977-1989)
➨ Chassis, running gear: Steering Peugeot 406 (1995-2004)
➨ Chassis, running gear: Steering Peugeot 605 (1989-2000)
➨ Chassis, running gear: Steering Peugeot 806 (1994-2002)
Link to this section in different formats
TEXTHTMLBB Code
- General information
- Car care
- Governing bodies
- Driving and operation
- Power unit
- Engine characteristics
- Engine repair
- Cooling system
- Lubrication system
- Ignition system
- Control system (gasoline)
- Fuel system (gasoline)
- Control system (diesel)
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Car suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Headlights and lighting
- Power devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Gasoline engines
- Diesel engines
- Diesel power system
- Engine management system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Body elements
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits