Car diesel power system Peugeot 206

General information about the fuel system of diesel engines
The fuel system includes a fuel tank located at the rear under the body; a fuel lift pump submerged in the tank, a fuel filter with a water separator, a high-pressure fuel pump (HPFP), fuel injectors and connecting fuel...

Removal and installation the fuel filter of the DW8 engine
Remove the fuel filter in the following order: Figure 4.84. Preparing to remove the fuel filter: 1 - Snap-on connector; 2 - drain hole; 3 - clamp; 4 - fuel filter cover remove the engine protective cover; Caution!...

Removal and installation the fuel filter of the DW10 TD engine
When removing and installing the fuel filter at Peugeot service centers, the following special tool is used: set of plugs 0188-T; sODIMAC solvent No.35 (supplied as spare parts); brush; cleaning tank. Remove the fuel...

Removal and installation fuel injectors on the DW8 engine
When removing and installing fuel injectors at Peugeot service centers, they use the 0149 injector bushing. Remove the fuel injectors in the following order: disconnect the negative battery cable; Figure 4.91. Removing...

Removal and installation fuel injectors of the DW10 TD engine
The injectors are marked by engraving or paint on the top of the winding on the side of the fuel return hole: mark 1 (in the form of a blue paint spot - class 1 nozzle); mark 2 (in the form of a green paint spot - class...

Removal and installation the high pressure fuel regulator on the high pressure fuel pump
Remove the high pressure fuel regulator on the high pressure fuel pump in the following order: remove the engine protective cover; disconnect the negative battery cable; Figure 4.99. Preparing to remove the fuel...

Removal and installation the fuel distributor
When removing and installing the fuel distributor, Peugeot service centers use the following special tool: torque Wrench 1603-A/B/D; pipe wrenches - 1603-G and 1603-F; extension cord 1603-E; set of plugs 0188-T. Remove...

Removal and installation of fuel injection pump
When removing and installing the injection pump at Peugeot service centers, the following special tool is used: crossbar 0102-D; chain for lifting and hanging 0102-M; pin for fixing the pulley in a fixed position -...

Removal and installation of fuel injection pumps from LUCAS
When removing and installing the LUCAS high-pressure fuel pump, Peugeot service centres use the following special tool: lUCAS high pressure pump adjustment device - (0188-H); electronic engine immobilizer. Note: This is...

Checking and adjusting the fuel injection pump
Adjusting the fast idle mode Adjust the fast idle speed on a cold engine in the following order: Figure 4.118. Adjusting the fuel injection pump: 1, 2, 8 - levers; 3 - pin; 4 - gasket; 5 - stop screw; 6 - limit screw; 7...

Turbocharging system — general information
One of the parameters that determine engine power is cylinder filling. Using a turbocharging system allows air to be forced into the intake manifold under pressure, and this somewhat extends the cylinder filling cycle....

Removal and installation of turbocharger DW10 TD
Remove the turbocharger in the following order: remove the front right wheel; remove the front right mudguard; remove the protective screens under the power unit; drain the oil from the gearbox; Caution! Remove the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

See similar information for other Peugeot models

➨ Power unit: Fuel system (diesel) Peugeot 106 (1991-2003)
➨ Power unit: Fuel system (gasoline) Peugeot 305 (1977-1989)
➨ Power unit: Fuel system (carburetor) Peugeot 405 (1987-1997)
➨ Power unit: Fuel system Peugeot 605 (1989-2000)
➨ Power unit: Power and exhaust (XUD diesels) Peugeot Partner I (1996-2008)

Link to this section in different formats

TEXTHTMLBB Code