Share information:
Electrical equipment and devices of the car Peugeot 206
The on-board circuit is powered by a lead-acid battery that is charged by the alternator. When working with any element of electrical equipment, it is necessary to disconnect the wire from the negative terminal of the battery.
Technical data of electrical equipment
Technical data Type single-wire circuit, on-board network voltage 12 V Lamp power, W: front fog lights 55 front side lights 55 direction indicators 21 side turn signal repeater 5 brake signal in rear lights 21/5 fog...
Technical data Type single-wire circuit, on-board network voltage 12 V Lamp power, W: front fog lights 55 front side lights 55 direction indicators 21 side turn signal repeater 5 brake signal in rear lights 21/5 fog...
Finding a faulty consumer in an electrical system
If you notice that a fully functional battery has started to discharge when the engine is not running and consumers are switched off, this means that there is a current leak in the on-board network, which may be caused...
If you notice that a fully functional battery has started to discharge when the engine is not running and consumers are switched off, this means that there is a current leak in the on-board network, which may be caused...
Detecting the source of a short circuit
Detect the source of the short circuit in the following order: disconnect electrical consumers; remove the appropriate fuse and connect the multimeter leads to the fuse leads; apply power to the circuits, remembering...
Detect the source of the short circuit in the following order: disconnect electrical consumers; remove the appropriate fuse and connect the multimeter leads to the fuse leads; apply power to the circuits, remembering...
Removal and installation the generator
Diesel engine DW8 Remove the generator in the following order: disconnect the negative battery cable; disconnect the contact connector from the control unit; remove the decorative engine cover; remove the accessory...
Diesel engine DW8 Remove the generator in the following order: disconnect the negative battery cable; disconnect the contact connector from the control unit; remove the decorative engine cover; remove the accessory...
Removal and installation windshield wiper arms
Remove the windshield wiper arms in the following order: turn the windshield wiper motor on and then off; apply adhesive tape to the glass along the wiper blade to mark the original position of the blade; Figure 10.8....
Remove the windshield wiper arms in the following order: turn the windshield wiper motor on and then off; apply adhesive tape to the glass along the wiper blade to mark the original position of the blade; Figure 10.8....
Removal and installation the windshield wiper electric drive
To remove the windshield wiper motor, follow these steps: disconnect the negative battery cable; remove the wiper arms from the shafts; on petrol models, remove the air duct connecting the air cleaner to the intake...
To remove the windshield wiper motor, follow these steps: disconnect the negative battery cable; remove the wiper arms from the shafts; on petrol models, remove the air duct connecting the air cleaner to the intake...
Removal and installation the electric drive of the windshield wiper of the luggage compartment door
To remove the electric drive of the luggage compartment windshield wiper, proceed as follows: disconnect the negative battery cable; remove the windshield wiper arm; open the trunk door and remove the trim panel from...
To remove the electric drive of the luggage compartment windshield wiper, proceed as follows: disconnect the negative battery cable; remove the windshield wiper arm; open the trunk door and remove the trim panel from...
Relay and fuse box
Fuses are designed to interrupt the current in a circuit when it exceeds a certain value, which can lead to the destruction of circuit parts. An increase in current in a circuit is a consequence of its malfunction,...
Fuses are designed to interrupt the current in a circuit when it exceeds a certain value, which can lead to the destruction of circuit parts. An increase in current in a circuit is a consequence of its malfunction,...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See similar information for other Peugeot models
➨ Electrical equipment: Equipment and devices Peugeot 106 (1991-2003)
➨ Electrical equipment: Equipment and devices Peugeot 307 (2001-2008)
➨ Electrical equipment: Equipment and devices Peugeot 405 (1987-1997)
➨ Electrical equipment: Equipment and devices Peugeot Partner I (1996-2008)
Link to this section in different formats
TEXTHTMLBB Code
- General information
- Car care
- Governing bodies
- Driving and operation
- Power unit
- Engine characteristics
- Engine repair
- Cooling system
- Lubrication system
- Ignition system
- Control system (gasoline)
- Fuel system (gasoline)
- Control system (diesel)
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Car suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Headlights and lighting
- Power devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Gasoline engines
- Diesel engines
- Diesel power system
- Engine management system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Body elements
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits