Car steering Peugeot 207

General information about steering
The electro-hydraulic power steering operates on signals from the controlled electric unit, which allows the gain to be changed depending on the following parameters: car speed; steering wheel speed; power steering...

Steering column identification
Left-hand or right-hand steering column is identified by the color of the sticker (in zone "a"). Left-hand: black. Right side: yellow.

Tightening torques for steering components
Steering column Steering gear The steering gear with an integrated slave cylinder is mounted on the front frame using two studs. The power steering valve has grooves. The supply and return pipes of the hydraulic circuit...

Technical characteristics of the steering system

Executive mechanism (power steering electric pump unit)
Power steering pump unit: 1 - support of the electric pump unit of the power steering; 2 - electric motor; a - signal connector; b - power electrical connector. . The electric power steering pump unit supplies the...

Power steering pump control unit
The ECU is installed in the power steering pump unit block. There are two electronic boards in the ECU (the operation of electronic equipment is ensured by a microprocessor and a self-diagnostic system). The ECU...

Steering wheel angle sensor
The steering wheel angle sensor is part of the switching unit under the steering wheel. The sensor detects the direction of rotation of the steering wheel and its rotation speed. It sends this information to the control...

Checking the pressure in the power steering circuit
Special devices for checking the pressure in the power steering circuit: 1 - pressure gauge 0710.AZ; 2 - branch pipe for testing with a pressure gauge with a tap 0710. B1; 3 - branch pipe for testing high pressure hose...

Draining fluid from the hydraulic circuit of the power steering
Caution: Open the circuit carefully to prevent contamination particles from entering it. Use new fluid to bleed and refill the hydraulic steering circuit. Note: The power steering circuit must be drained with the engine...

Filling the hydraulic circuit of the power steering
Caution: Open the circuit carefully to prevent contamination particles from entering it. Install new gaskets (4). Install the clamp (3), bolt (2) and screw in area "a". Install the steering gear heat shield.

Bleeding the hydraulic circuit of the power steering
Fill the power steering fluid reservoir to the maximum mark. Slowly turn the steering wheel from one extreme position to the other in both directions about ten times (with the engine off). Top up the working fluid to...

Removal and installation the steering wheel
Driver's airbag Set the steering wheel to a horizontal position to gain access to the service hole (in area "a"). Insert a flat-blade screwdriver and press it to release the module retaining spring (1) by pressing on...

Removal and installation the steering wheel angle sensor
Removal Remove: driver's airbag (see the corresponding operation); steering wheel (see the corresponding operation). Disconnect the steering wheel angle sensor (1) in area "a". Disconnect the connector in area "b"...

Removal and installation of steering rods
Special devices: 1 - device for blocking the steering rack from turning 0721.B; 2 - tubular wrench 0721.A; 3 - steering rod ball joint puller 1892-T; 4 - clamp pliers "Clic" 0172.Z. Removal Secure and raise the vehicle...

Adjusting the rack's middle position
Secure and raise the vehicle on a two-post lifting platform. Remove (on the right) clamps (1) and (2). Remove the steering rack protective cover. Adjustment Measure the size "X". Turn the steering wheel to the extreme...

Removal and installation the steering gear
Removal Place the car on a lift. Note: Set the front wheels straight ahead and lock the steering wheel in this position. Remove the front subframe (see the corresponding operation). Loosen the nuts (1) of the studs and...

Adjusting the steering rack stop
Special devices: 1 - tip "Allen Facom" ST.17; 2 - tap for steering gear 8612-T. Removal Remove the steering gear (see the corresponding operation) and secure it in a vice equipped with pads. Remove: plug (1) using tool...

Removal and installation the steering column
Removal Remove the driver's airbag. Make a mark to ensure the steering wheel is in the correct position after reinstallation. Remove the steering wheel. Loosen the bolt (2) of the steering column cardan shaft. Turn on...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

See similar information for other Peugeot models

➨ Chassis, running gear: Steering Peugeot 106 (1991-2003)
➨ Chassis, running gear: Steering system Peugeot 306 (1993-2002)
➨ Chassis, running gear: Steering Peugeot 406 (1995-2004)
➨ Chassis, running gear: Steering Peugeot 605 (1989-2000)
➨ Chassis, running gear: Steering Peugeot 806 (1994-2002)

Link to this section in different formats

TEXTHTMLBB Code