Car front and rear suspension Peugeot 207

Front axle
The Peugeot 207 is equipped with a pseudo-MacPherson type front axle with independent front wheels and an anti-roll bar (diameter 20 or 21 mm). A "compressed type" steering knuckle, in which a double-row ball bearing is...

Rear axle
The rear axle is welded mechanically in the form of stretchable levers with a deformable axle cross member without an anti-roll bar. Rear axle: 1 - rear axle crossmember; 2 - cap for fixing the rear axle crossmember to...

Geometry of bridges
Note: Checking the wheel alignment may affect the nominal or loaded draft. Note: Curb vehicle: vehicle without payload, filled with fuel, tire pressure is correct. Setting the suspension to the middle position (H1-H2)...

General characteristics and tightening torques of the front suspension
Steering knuckle Front stabilizer bar Geometry of front and rear axles "A" is less than "B": positive toe-in (+). "A" is greater than "B": negative toe-in (-). Adjusting the front wheel alignment Set the vehicle to a...

Front axle alignment angles
Attention: To check all angles (longitudinal inclination angles of steering knuckles, toe-in, parallelism) it is necessary to set the car to the middle working position.

General characteristics and tightening torques of the rear suspension
Characteristics Attention: To check all angles (longitudinal inclination angles of steering knuckles, toe-in, parallelism) it is necessary to set the car to the middle working position. Tightening torques * TOTAL N3373...

Removal and installation the front suspension steering knuckle
Removal Raise and block the car, raising the front wheels. Remove the wheel. Using the tool [1], lock the hub to prevent it from rotating. Loosen the drive shaft nut. Caution: When loosening the drive shaft nut, do not...

Removal and installation the lower front arm
Removal Raise and block the car, raising the front wheels. Remove the wheel. Loosen the steering knuckle ball joint bolt (1). Move the suspension arm to the ball joint level. Loosen the bolts (2) and remove the lower...

Removal and installation the ball joint of the front steering knuckle
Special device: 1 - centering tap 0621/3-B Removal Caution: Check the condition of the suspension arm after removing the rivets. If there is surface marking or paint peeling, apply anti-corrosion black paint. If...

Lower Front Arm Repair
Special devices: 1 - thrust cap 0621-N; 2 - mounting mandrel 0621-M; 3 - mounting mandrel 0621/3-D; 4 - mounting mandrel 0621/3-C. Remove the front lower control arm (see the corresponding operation). Removal (rear...

Front steering knuckle repair
Special devices: 1 - extractor "Facom" L53 (K2+T2) 4108-T; 2 - screw 9501-T.A; 3 - bearing extractor support plate 0621.B; 4 - nut 9501-T.C1; 5 - puller 9501-T.D4 + 9501-T.D5; 6 - auxiliary insert 9501-T.C2; 7 - bearing...

Features of front suspension wheel bearings
Caution: Use new bearing and snap rings. Lightly lubricate the bearing seat in the steering knuckle housing and the hub itself. The parts must be clean and free of any signs of abnormal wear or impact. Do not place the...

Removal and installation the front subframe and frame
Special devices: 1 - Ball joint puller 0709; 2 - lever for separating the ball joints of the steering knuckle 0622. Removal Raise and block the vehicle, raising the front wheels. Remove: front wheels; front mudguards;...

Removal and installation the stabilizer bar
Special devices: 1 - mixed type key; 2a - key Togh; 2b - BTR key. Removal Caution: When performing the operation, be careful not to damage the rack hinge (1). Secure the hinge tail using tool 2. Unscrew the nut (2)...

Removal and installation the front anti-roll bar
Removal Raise and block the vehicle, raising the front wheels. Remove the front subframe. Loosen the bolts (1) and remove the assembly: anti-roll bar/supports. Identification of lids The anti-roll bar is hingedly...

Removal and installation the front shock absorber assembly
Special devices: 1 - hub locking device 0606-AY; 2 - lever for separating the ball joints of the steering knuckle 0622; 3 - Ball joint puller 0903-AF. Removal Raise and block the vehicle, raising the front wheels....

Disassembling the front shock absorber (on the workbench)
Special devices: 1 - spring compression device 4137-T M90; 2a - fixed cup 4137-T M2R; 2b - movable cup 4137-T M2C. Note: Check the presence and condition of the protective rubber caps on the Fixed and Sliding Cups of...

Removal and installation the rear wheel hub
Removal Secure and raise the vehicle on a two-post lifting platform. Remove the wheel. Unscrew the three bolts (1) and remove the protective shield (2). Unscrew the bolt (3) and remove the ABS sensor (4). Remove the...

Removal and installation the rear wheel trunnion
Removal Raise and secure the vehicle with the rear wheels off the ground. Remove the rear wheel, hub and rear brake disc (see the corresponding operation). Loosen the bolt (1). Move the ABS sensor (2). Loosen the bolts...

Removal and installation the rear axle
Removal Raise and secure the vehicle in the raised position (use a two-post lift). Remove the rear wheels. A: left side. B: right side. Unscrew the bolts (1) and remove the protective element (2). Cars with rear drum...

Removal and installation rear suspension silent blocks
Removal Remove the rear axle. Loosen the bolt (1) and remove the casing (2). Special devices: 1 - insert for installing elastic hinge 0549-C1; 2 - counter stop for removal and installation 0549-D1/0549-E3; 3-insert for...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

See similar information for other Peugeot models

➨ Chassis, running gear: Car suspension Peugeot 106 (1991-2003)
➨ Chassis, running gear: Car suspension Peugeot 305 (1977-1989)
➨ Chassis, running gear: Car suspension Peugeot 406 (1995-2004)
➨ Chassis, running gear: Car suspension Peugeot 605 (1989-2000)
➨ Chassis, running gear: Car suspension Peugeot Partner I (1996-2008)

Link to this section in different formats

TEXTHTMLBB Code