Table of contents: Headlight 🠇 Front direction indicator 🠇 Front side turn signal repeater 🠇 Front fog lights 🠇 Rear light (sedan models) 🠇 Rear light (combi models) 🠇 License plate light (sedan models) 🠇 License plate light (combi models) 🠇
Caution: Disconnect the negative cable from the battery before removing any light and reconnect the negative cable to the battery after installing the light.
Headlight
Attention! Before removing the optical units of the headlights, it is necessary to mark on the wall (for example, in an underground garage) the light trail from the low and high beam headlights, as well as the position of all four wheels.
Removal
1. Working in the engine compartment, release the bracket securing the cover to the rear of the headlight.
2. Disconnect the wires from the incandescent bulbs located in the headlight.
3. Working in the engine compartment, disconnect the front turn signal lamp retaining spring from the protrusion.
4. Remove the front turn signal from the fender.
5. On models with headlight range control, disconnect the range control from the headlight as follows.
6. Remove the corrector housing from the suspension on the front panel.
7. Remove the ball joint from the socket at the rear of the headlight.
8. On models with electrically controlled headlight range control, disconnect the wires from the range control at the rear of the headlight.
The source is located on the website: www.peugeotbook.ru
9. Remove the radiator grille.
10. Unhook the bar located under the headlight, being careful not to damage the fastening near the edge of the wing.
11. Unscrew two (indicated by an arrow) outer headlight mounting bolts and pull the headlight forward from the body panel.
12. Remove the metal clamps securing the glass to the headlight and remove the glass from the headlight.
13. Before installing the headlight glass, check that the seal located in the groove around the perimeter of the headlight is in good condition.
Installation
1. Installation is carried out in the reverse order of removal.
2. Adjust the headlights as soon as possible.
Front direction indicator
1. Working in the engine compartment, disconnect the front turn signal lamp retaining spring from the protrusion.
2. Remove the front turn signal from the fender.
Front side turn signal repeater
Turn the front side turn signal repeater counterclockwise and remove it from the vehicle fender.
Front fog lights
Two types of headlights can be installed. The headlights can be installed either directly in the front spoiler or in a socket screwed to the front spoiler.
Fog light installed in spoiler socket
1. At the rear of the spoiler, disconnect the electrical connector from the headlight.
2. Unscrew two screws (indicated by an arrow) fastening the fog light to the spoiler, then remove the light with the socket from the spoiler.
3. Unscrew the nut (indicated by the arrow) fasteners at the rear of the headlight and remove the headlight from the socket.
4. Installation is carried out in the reverse order of removal.
5. Check and, if necessary, adjust the headlight beam using the knurled nuts at the rear of the headlight.
Headlight mounted directly into the spoiler
Please note: Some models are equipped with front fog lights that do not have mounting screws visible from the side of the headlight glass.
6. Raise the front of the vehicle and secure it on stands.
7. Trace the wiring back from the fog light and disconnect the electrical connector.
8. Unscrew the mounting nuts and remove the headlight from the spoiler.
9. Installation is carried out in the reverse order of removal.
Rear light (sedan models)
1. Open the trunk lid.
2. Squeeze the two mounting brackets and remove the bulb holder from the rear light.
3. Disconnect the electrical connector from the bulb holder.
4. Remove the luggage compartment trim.
5. Unscrew the nuts (indicated by arrows) rear light mounts.
6. Remove the rear light, first removing the outer part of the light.
7. Installation is carried out in the reverse order of removal.
Rear light (combi models)
The brake light and turn signal lights are located in the rear wing. The remaining rear light bulbs are located in the rear door.
1. Open the back door.
2. Turn the fastening bracket and open the luggage compartment cover flap.
3. Squeeze the two mounting brackets and remove the bulb holder from the rear light.
4. Disconnect the electrical connector from the bulb holder.
5. Unscrew the nuts (indicated by arrows) rear light mounts.
6. Unscrew the nuts (indicated by arrows) fastening the rear light to the door.
7. Remove the rear light.
8. Installation is carried out in the reverse order of removal.
License plate light (sedan models)
1. Unscrew two screws (indicated by arrows) fasteners, then remove the backlight from the bumper and disconnect the electrical connector.
2. Installation is carried out in the reverse order of removal.
License plate light (combi models)
1. Using a lever, remove the license plate light from the rear door and disconnect the electrical connector.
2. Installation is carried out in the reverse order of removal.