Installing the crankshaft (Peugeot J5)
The description of the crankshaft installation is given in connection with the engine assembly in section 20.3. It is imperative to install both expansion washers of the same thickness. Tighten the fasteners, observing the specified tightening torque values. Rotate the crankshaft evenly to immediately detect any possible jamming at a certain stage of assembly.
This article is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Article reviewed by editor: Bespalov Alexey
Share information:
See similar information for other Peugeot models
➨ Crankshaft oil seals — renewal Peugeot 106 (1991-2003)
➨ Crankshaft characteristics (petrol engines 1.4 and 1.6 l, EPZ,… Peugeot 207 (2006-2014)
➨ Installing the crankshaft Peugeot 306 (1993-2002)
➨ Installing the crankshaft (XU and XUD engines) Peugeot 406 (1995-2004)
➨ Front crankshaft oil seal (timing belt side) — replacement Peugeot 605 (1989-2000)
Link to this article in different formats
Comments and feedback from visitors
No comments yet
- General information
- Introduction to the guide
- Faults en route
- Weekly checks
- User manual
- Maintenance (petrol)
- Maintenance (diesel)
- Power unit
- Petrol engines
- Diesel engines «XUD»
- Diesel engines «DW»
- Overhaul of petrol engines
- Overhaul of diesel engines
- Cooling and heating
- Power and exhaust (petrol)
- Power and exhaust (XUD diesels)
- Power and exhaust (DW diesels)
- Emission reduction
- Starting and charging system
- Transmission
- Clutch
- Mechanical gearbox
- Drive shafts
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- Operating instructions
- Maintenance
- Troubleshooting
- Power unit
- Gasoline engines
- Diesel engines
- Cooling and heating
- Fuel injection (petrol)
- Fuel system (diesel)
- Fuel system
- Exhaust system
- Ignition system
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Chassis, running gear
- Brake system
- Car suspension
- Steering system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Power devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Petrol engines
- Diesel engines
- Lubrication system
- Cooling system
- Fuel injection (petrol)
- Fuel system (diesel)
- Ignition and exhaust systems
- ECM Bosch Motronic MP 3.2
- ECM Magneti-Marelli (MM)
- Transmission
- Clutch
- Mechanical gearbox
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- Introduction to manual
- Specifications
- Gasoline engine
- Engine repair
- Lubrication system
- Cooling system
- Fuel system
- Ignition system
- Diesel engine
- Engine repair (DB9)
- Lubrication system (DB9)
- Cooling system (DB9)
- Fuel injection (DB9)
- Engine repair (U25)
- Lubrication system (U25)
- Cooling system (U25)
- Fuel injection (U25)
- Transmission
- Clutch
- Gearbox
- Drive shafts
- Chassis, running gear
- Steering system
- Car suspension
- Brake system
- Electrical equipment
- Power devices
- Electrical circuits