Power supply and exhaust system of gasoline engine Peugeot Partner 1

Fuel and exhaust system specifications
System type Models with 1.4L engine: KFX Engines: Models up to 1999 - Magneti Marelli 1 AP Models since 1999: L3 emission standard - Sagem Lucas SL96 Emission standard L4 - Bosch Motronic MP7.3 KFW engines - Sagem S2000...

General information and precautions
The fuel system includes a fuel tank (mounted under the rear of the car), electric fuel pump (immersed in a tank), fuel filter, fuel supply lines and fuel return lines (on early models). The fuel pump delivers fuel to...

Air cleaner assembly and air intake ducts — removal and installation
Note: If the hoses are secured with clamps or wire ties, cut and discard them. Use standard worm-type clamps or new wire ties for installation. Removal Models produced before September 2002 with a 1.4 L engine 1....

Accelerator cable — removal, installation and adjustment
Removal 1. Disconnect the accelerator cable from the cam on the throttle body or from the accelerator pedal position sensor, and then pull the cable housing out of the corresponding rubber grommet on the support...

Accelerator pedal removal and installation
Removal 1. Disconnect the accelerator cable from the pedal as described in previous paragraph . Right-hand drive models 2. Loosen the nut at the end of the pedal axle, holding the axle with an open-end wrench by the...

Unleaded Gasoline — general information and uses
Note: The information presented in this paragraph was correct at the time of writing. For the latest information, please contact your Peugeot/Citroën dealer. If you plan to travel abroad, consult an engine or fuel...

Engine Management System — general information
Note: The fuel injection electronic control unit (ECU) features a "self-learning" function. This means that while the engine is running, the ECU monitors and records settings that ensure optimal engine performance under...

Fuel system — pressure relief and pressure increase
Note: Before you begin, please read the warning provided in paragraph 1 . Pressure relief Caution: The following procedure will only relieve pressure in the fuel system, but remember that fuel still remains in the...

Fuel pump — removal and installation
Removal 1. Remove the fuel tank as described in paragraph 10 . 2. Press the locking elements on the quick release coupling and disconnect the fuel line from the top of the pump. Cap the end of the fuel line to prevent...

Fuel level indicator sensor — removal and installation
The fuel level gauge sensor is an integral part of the fuel pump and is not supplied separately. For removal and installation information, please refer to paragraph 8 .

Fuel tank — removal and installation
Note: Before you begin, please read the warning provided in paragraph 1 . Removal 1. Before removing the tank, drain as much fuel from it as possible. Since there is no drain plug, it is preferable to remove the tank...

Engine management system — checking and adjustment
Examination 1. If a malfunction occurs in the engine management system, first check that all electrical connectors in the system are securely connected and that they are not corroded. Make sure that the malfunction is...

Throttle body — removal and installation
Removal 1. Remove the air cleaner assembly as described in paragraph 2 . 2. Disconnect the accelerator cable from the throttle cam (if applicable). 3. Mark the installation position of the electrical connectors on the...

Fuel rail and injectors
Note: Before you begin, please read the warning provided in paragraph 1 . Note: If you suspect a faulty injector, try using one of the commercially available injector cleaners before removing the injectors. Models with...

Fuel pressure regulator
Note: The following procedure applies to models where the fuel pressure regulator is mounted on the fuel rail. On later models, the regulator is mounted on the top of the fuel tank or combined with the fuel pump. The...

Throttle potentiometer
Note: On 1.6L engine models with the Sagem S2000 system and all 1.6L engine models, the throttle potentiometer is an integral part of the throttle body and cannot be removed. 21. Disconnect the ground cable from the...

Electronic control unit
Note: If a new electronic control unit (ECU) needs to be installed, this work should be entrusted to a Peugeot/Citroën dealer. After installing the new ECU, it must be initialized, which requires the use of specialized...

Stepper motor for adjusting the crankshaft speed in idle mode
Note: On 1L engine models with the Sagem S2000 system and all 1.6L engine models, the stepper motor is an integral part of the throttle body and cannot be removed. 37. The stepper motor for adjusting the crankshaft...

Engine management system sensors
Manifold pressure sensor 41. The manifold pressure sensor is mounted on the front of the intake manifold. 42. Disconnect the ground cable from the battery (see " Disconnecting the battery "). 43. Disconnect the...

Intake manifold removal and installation
Removal Models with 1.4L engine 1. Remove the air cleaner assembly as described in paragraph 2 . 2. Remove the fuel rail and injectors as described in paragraph 13 . 3. If you have not already done so, disconnect the...

Exhaust manifold — removal and installation
Removal 1. On models with a 1.4L engine with secondary air injection, remove the secondary air injection valve as described in chapter 4G . 2. Fully apply the parking brake. Raise the front of the vehicle and support it...

Exhaust system — general information, removal and installation
General information 1. On early models, the exhaust system consists of four sections: a downpipe, a catalytic converter, an intermediate pipe and a center muffler, and a rear pipe with a rear muffler. All sections are...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

See similar information for other Peugeot models

➨ Power unit: Fuel system (diesel) Peugeot 106 (1991-2003)
➨ Power unit: Fuel system (gasoline) Peugeot 207 (2006-2014)
➨ Power unit: Fuel system (gasoline) Peugeot 305 (1977-1989)
➨ Power unit: Fuel system (carburetor) Peugeot 405 (1987-1997)
➨ Power unit: Fuel system Peugeot 605 (1989-2000)

Link to this section in different formats

TEXTHTMLBB Code

Partner I (1996-2008)