Engine Specifications Gasoline engines With a working volume of 1.8 liters - LFW (L3) -XU7JP 2.0 liter displacement, 6 valves - RFU (L3) -XU10J2C With a displacement of 2.0 liters, 8 valves - RXG (L3) -XU10J2CTE With a displacement of 2.0...
General description of engines As a result of the cooperation of automobile companies PEUGEOT, CITROEN, FIAT and LANCIA in 1995, a new car model appeared, which went on sale under different names: Citroen Evasion, Peugeot 806, Fiat Ulysee or Lancia...
Vehicles with 1.8 liter engine Start of release - 1997. The engine has a working volume of 1761 cm 3 and power 66 kW (90 hp). Designated as «XU7 JP» and has the type code LFW. These engines are equipped with a Mignetti-Marelli multipoint fuel...
Vehicles with 2.0 liter engine The engine has a working volume of 1998 cm 3 . At the same time, the power plant based on this engine can be equipped with modified engines. Some vehicles are equipped with 8-valve engines with or without a...
Vehicles with 1.9 liter diesel engines The standard engine has a displacement of 1905 cm 3 and power 92 hp. (67.5 kW). Engine code «XUD9TF/L» (D8B). If the engine is equipped with an oxidation type catalyst and an exhaust gas recirculation system, then its...
Vehicles with a 2.1 liter diesel engine The working volume of this engine is 2088 cm 3 , and power - 110 hp. (80 kW). The engine has the designation «XUD11BTE» RVS type. This engine has three valves per cylinder and a Lucas-developed EPIC power system. The...
Vehicle and engine identification The vehicle identification number is located under the hood on the right pillar of the front fender mudguard (see illustration 1.0). 1.0 Location of main numbers and plates 1 - identification number 2 - manufacturer...
Power unit — removal and installation Removing When performing work on the engine, it is necessary to take into account some features, which in turn allow us to conditionally divide all engines into three groups. These are engines without a catalyst,...
Engine installation The installation of the power unit is carried out in the reverse order of removal. In doing so, certain instructions applicable to all types of motors must be observed. 27. Replace all self-locking nuts, lock washers,...
Engine — disassembly Before carrying out work related to engine disassembly, thoroughly clean the surface of the engine. Before doing this, all openings on the engine should be covered with a clean rag so that dirt does not get inside. It...
Engine — complete disassembly The dismantled engine can be disassembled completely. The procedure for disassembling the engine is as follows (don't forget the difference between an 8 valve engine and a 16 valve engine). XU10 engines 1. Drain the...
Engine — Assembly When assembling a disassembled engine, the following rules must be observed. 1. Make sure all parts are clean. 2. Lubricate all moving parts with a thin layer of grease. Lubricate these parts before installing them, and...
Cylinder head — removal and installation The cylinder head can be removed without removing the engine from the vehicle. 1. Remove spark plugs if not already done. 2. Turn out a bolt of fastening of a gear wheel of a gear wheel on a camshaft. Remove the...
Gas distribution mechanism — bulkhead We do not recommend that you overhaul the gas distribution mechanism yourself. In the event that wear or damage to parts is revealed during the inspection of the mechanism, the engine should be delivered to a workshop...
Gas distribution mechanism — assembly When replacing the cylinder head, all parts from the old head must be installed on a new one. The following procedure for replacing the cylinder head refers to the rearrangement of parts from the previous head without...
Valve clearance — adjustment Valve clearance adjustment is only available on XU7 engines (volume 1.8 liters) and on XU10 engines with 8 valves. XU 10 engines with two camshafts and 16 valves have hydraulic tappets that do not need to be adjusted....
Pistons and connecting rods — disassembly, inspection and assembly Replacing pistons and working cylinder liners can only be carried out on a removed power unit after disconnecting the gearbox. When purchasing new cylinder liners and pistons, remember that they must be matched to each...
Cylinder block The cylinder block consists of a crankcase and the cylinder block itself, in which there are holes for cylinder liners, or the cylinder block can be cast from gray cast iron with drilled cylinder holes. When completely...
Crankshaft and flywheel — removal, inspection and installation The crankshaft is five-bearing. The necks of the main and connecting rod bearings can be reground with a decrease in their diameter to the nearest repair size. This means that the bearing shells can be replaced...
Toothed belt — removal and installation The drive of the gas distribution mechanism for all engines is carried out by a toothed belt, the tension of which is regulated by a tensioner. Checking the tension of the toothed belt is carried out using special...
Using special tools to adjust the timing mechanism In many cases, a car enthusiast can use special tools by borrowing them for a while or by purchasing them for personal use. Below are the main points regarding the use of the tools. The device with which the tension of...
Compression — check To check the functioning of the valves, the condition of the piston rings, as well as the cylinders as a whole, it is necessary to perform a compression pressure test on each cylinder. To perform the check, the engine...