At the factory, the system is filled with a coolant that is not recommended to be drained for a year, because it contains additives that protect the cooling system from corrosion and similar damage. When replacing coolant, we recommend using the coolant recommended by the vehicle manufacturer. This fluid is specially selected for the engine. If you use other brands of coolant, make sure that this liquid is suitable for your vehicle's engine. A coolant consisting of 50% antifreeze and 50% water will provide protection against freezing at all sub-zero temperatures down to -30°C.
If you need to add water to the system while driving, remember that this will change the concentration of the coolant. By the time the cold weather sets in, people usually forget that water was added to the system in the summer. Therefore, it is recommended to use a hydrometer at the gas station and check the concentration of the coolant, and add antifreeze if necessary.
Original published on the portal [Peugeotbook.ru]
Cooling liquid (Peugeot Eurovans 806)
This article is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Article reviewed by editor: Shirokov Arseny
Share information:
See similar information for other Peugeot models
➨ Cooling, heating and ventilation systems — specifications Peugeot 106 (1991-2003)
➨ Cooling liquid Peugeot 207 (2006-2014)
➨ Cooling system specification Peugeot 305 (1977-1989)
➨ Engine post-cooling Peugeot 405 (1987-1997)
➨ Checking the cooling system Peugeot 605 (1989-2000)
Link to this article in different formats
Comments and feedback from visitors
No comments yet
- General information
- Introduction to the guide
- Faults en route
- Weekly checks
- User manual
- Maintenance (petrol)
- Maintenance (diesel)
- Power unit
- Petrol engines
- Diesel engines «XUD»
- Diesel engines «DW»
- Overhaul of petrol engines
- Overhaul of diesel engines
- Cooling and heating
- Power and exhaust (petrol)
- Power and exhaust (XUD diesels)
- Power and exhaust (DW diesels)
- Emission reduction
- Starting and charging system
- Transmission
- Clutch
- Mechanical gearbox
- Drive shafts
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- Operating instructions
- Maintenance
- Troubleshooting
- Power unit
- Gasoline engines
- Diesel engines
- Cooling and heating
- Fuel injection (petrol)
- Fuel system (diesel)
- Fuel system
- Exhaust system
- Ignition system
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Chassis, running gear
- Brake system
- Car suspension
- Steering system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Power devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Petrol engines
- Diesel engines
- Lubrication system
- Cooling system
- Fuel injection (petrol)
- Fuel system (diesel)
- Ignition and exhaust systems
- ECM Bosch Motronic MP 3.2
- ECM Magneti-Marelli (MM)
- Transmission
- Clutch
- Mechanical gearbox
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- Introduction to manual
- Specifications
- Gasoline engine
- Engine repair
- Lubrication system
- Cooling system
- Fuel system
- Ignition system
- Diesel engine
- Engine repair (DB9)
- Lubrication system (DB9)
- Cooling system (DB9)
- Fuel injection (DB9)
- Engine repair (U25)
- Lubrication system (U25)
- Cooling system (U25)
- Fuel injection (U25)
- Transmission
- Clutch
- Gearbox
- Drive shafts
- Chassis, running gear
- Steering system
- Car suspension
- Brake system
- Electrical equipment
- Power devices
- Electrical circuits
