The installation of an oil radiator is shown on figure 310. The oil radiator is flushed with coolant, meaning that when removing the oil radiator, the coolant must be drained and the oil filter removed.
After disconnecting the water hoses, unscrew the connecting sleeve in the middle of the oil radiator and remove the filter, as well as the base sealing ring.
When installing, put a new gasket, place the oil cooler in the correct position and screw in the connecting sleeve. Tighten the bushing to a torque of 85 Nm.
Install the oil filter according to the instructions section 21.2.
Oil radiator (Peugeot J5)
This article is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Article reviewed by editor: Bespalov Alexey
Share information:
See similar information for other Peugeot models
➨ Radiator — removal, inspection and refitting Peugeot 106 (1991-2003)
➨ Removal and installation lower radiator hoses with quick-release… Peugeot 207 (2006-2014)
➨ Radiator — removal and installation Peugeot 305 (1977-1989)
➨ Oil radiator — removal and installation Peugeot 405 (1987-1997)
➨ Radiator — removal and installation Peugeot 605 (1989-2000)
Link to this article in different formats
Comments and feedback from visitors
No comments yet
- General information
- Introduction to the guide
- Faults en route
- Weekly checks
- User manual
- Maintenance (petrol)
- Maintenance (diesel)
- Power unit
- Petrol engines
- Diesel engines «XUD»
- Diesel engines «DW»
- Overhaul of petrol engines
- Overhaul of diesel engines
- Cooling and heating
- Power and exhaust (petrol)
- Power and exhaust (XUD diesels)
- Power and exhaust (DW diesels)
- Emission reduction
- Starting and charging system
- Transmission
- Clutch
- Mechanical gearbox
- Drive shafts
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- Operating instructions
- Maintenance
- Troubleshooting
- Power unit
- Gasoline engines
- Diesel engines
- Cooling and heating
- Fuel injection (petrol)
- Fuel system (diesel)
- Fuel system
- Exhaust system
- Ignition system
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Chassis, running gear
- Brake system
- Car suspension
- Steering system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Power devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Petrol engines
- Diesel engines
- Lubrication system
- Cooling system
- Fuel injection (petrol)
- Fuel system (diesel)
- Ignition and exhaust systems
- ECM Bosch Motronic MP 3.2
- ECM Magneti-Marelli (MM)
- Transmission
- Clutch
- Mechanical gearbox
- Chassis, running gear
- Brake system
- Car suspension
- Steering
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- Introduction to manual
- Specifications
- Gasoline engine
- Engine repair
- Lubrication system
- Cooling system
- Fuel system
- Ignition system
- Diesel engine
- Engine repair (DB9)
- Lubrication system (DB9)
- Cooling system (DB9)
- Fuel injection (DB9)
- Engine repair (U25)
- Lubrication system (U25)
- Cooling system (U25)
- Fuel injection (U25)
- Transmission
- Clutch
- Gearbox
- Drive shafts
- Chassis, running gear
- Steering system
- Car suspension
- Brake system
- Electrical equipment
- Power devices
- Electrical circuits