Coolant renewal (Peugeot 106)

Cooling system draining

Warning: Wait until the engine is cold before starting this procedure. Do not allow antifreeze to come In contact with your skin, or with the painted surfaces of the vehicle. Rinse off spills immediately with plenty of water. Never leave antifreeze lying around in an open container, or in a puddle in the driveway or on the garage floor. Children and pets are attracted by its sweet smell, but antifreeze can be fatal if ingested.

1. With the engine completely cold, remove the expansion tank filler cap. Turn the cap anti-clockwise until it reaches the first stop. Wait until any pressure remaining in the system is released, then push the cap down, turn it anti-clockwise to the second stop, and lift it off.

2. Position a suitable container beneath the coolant drain outlet at the lower left-hand side of the radiator.

3. Loosen the drain plug (there is no need to remove it completely) and allow the coolant to drain into the container. If desired, a length of tubing can be fitted to the drain outlet to direct the flow of coolant during draining.

4. To assist draining, open the cooling system bleed screws. These are located in the heater matrix outlet hose union (to improve access, it may be located in an extension hose), on the engine compartment bulkhead, and on the top of the thermostat housing. On some models, there may also be a bleed screw in the top left-hand end of the radiator.



5. When the flow of coolant stops, reposition the container below the cylinder block drain plug. The drain plug is located at the rear of the cylinder block.

6. Remove the drain plug, and allow the coolant to drain into the container.

7. If the coolant has been drained for a reason other than renewal, then provided it is clean and less than two years old, it can be re-used, though this is not recommended.

8. Refit the radiator and cylinder block drain plugs on completion of draining.

Cooling system flushing

9. If coolant renewal has been neglected, or if the antifreeze mixture has become diluted, then in time, the cooling system may gradually lose efficiency, as the coolant passages become restricted due to rust, scale deposits, and other sediment. The cooling system efficiency can be restored by flushing the system clean.

[Original text is located at: PeugeotBook.ru]

10. The radiator should be flushed independently of the engine, to avoid unnecessary contamination.

Radiator flushing

11. To flush the radiator, first tighten the radiator drain plug, and the radiator bleed screw, where applicable.

12. Disconnect the top and bottom hoses and any other relevant hoses from the radiator, with reference to Chapter 3.

13. Insert a garden hose into the radiator top inlet. Direct a flow of clean water through the radiator, and keep flushing until clean water emerges from the radiator bottom outlet.

14. If after a reasonable period, the water still does not run clear, the radiator can be flushed with a good proprietary cleaning agent. It is important that their manufacturer's instructions are followed carefully. If the contamination is particularly bad, insert the hose in the radiator bottom outlet, and reverse-flush the radiator.

Engine flushing

15. To flush the engine, first refit the cylinder block drain plug, and tighten the cooling system bleed screws.

16. Remove the thermostat as described in Chapter 3, then temporarily refit the thermostat cover.

17. With the top and bottom hoses disconnected from the radiator, insert a garden hose into the radiator top hose. Direct a clean flow of water through the engine, and continue flushing until clean water emerges from the radiator bottom hose.

18. On completion of flushing, refit the thermostat and reconnect the hoses with reference to Chapter 3.

Cooling system filling

19. Before attempting to fill the cooling system, make sure that all hoses and clips are in good condition, and that the clips are tight. An antifreeze mixture must be used all year round, to prevent corrosion of the engine components (see following sub-Section). Also check that the radiator and cylinder block drain plugs are in place and tight.

20. Remove the expansion tank filler cap.

21. Open all the cooling system bleed screws (see paragraph 4).

22. Some of the cooling system hoses are positioned at a higher level than the top of the radiator expansion tank. It is therefore necessary to use a "header tank" when refilling the cooling system, to reduce the possibility of air being trapped in the system. Although Peugeot dealers use a special header tank, the same effect can be achieved by using a suitable bottle, with a seal between the bottle and the expansion tank.

23. Fit the "header tank" to the expansion tank; the expansion tank breather hose should be clamped. Slowly fill the system. Coolant will emerge from each of the bleed screws in turn, starting with the lowest screw. As soon as coolant free from air bubbles emerges from the lowest screw, tighten that screw, and watch the next bleed screw in the system. Repeat the procedure until the coolant is emerging from the highest bleed screw in the cooling system and all bleed screws are securely tightened.



24. Ensure that the "header tank" is full (at least 0.5 litres of coolant). Start the engine, and run it at a fast idle speed (do not exceed 2000 rpm) until the cooling fan cuts in, and then cuts out. Stop the engine.

25. Allow the engine to cool, then remove the "header tank". Remove the clamp from the expansion tank breather hose.

Warning: Take great care not to scald yourself with the hot coolant during this operation.

26. When the engine has cooled, check the coolant level as described in "Weekly checks". Top-up the level if necessary, and refit the expansion tank cap.

Antifreeze mixture

27. The antifreeze should always be renewed at the specified intervals. This is necessary not only to maintain the antifreeze properties, but also to prevent corrosion which would otherwise occur as the corrosion inhibitors become progressively less effective.

28. Always use an ethylene-glycol based antifreeze which is suitable for use in mixed-metal cooling systems. The quantity of antifreeze and levels of protection are indicated in the Specifications.

29. Before adding antifreeze, the cooling system should be completely drained, preferably flushed, and all hoses checked for condition and security.

30. After filling with antifreeze, a label should be attached to the expansion tank, stating the type and concentration of antifreeze used, and the date installed. Any subsequent topping-up should be made with the same type and concentration of antifreeze.

31. Do not use engine antifreeze in the windscreen/tailgate washer system, as it will cause damage to the vehicle paintwork. A screenwash additive should be added to the washer system in the quantities stated on the bottle.