Brake system of the car Peugeot 307

General information about the braking system
According to its purpose and functions, the braking system is divided into service, spare, parking and emergency. The service braking system ensures that the vehicle speed is regulated and stopped with the required...

Technical characteristics of the brake system
Tables 8.1, 8.2, 8.3, 8.4, 8.5 show the main technical characteristics of the Peugeot 307 braking system.

Replacing the brake master cylinder
An extra-short 23.8mm diameter master cylinder is fitted to all cold climate versions and versions with automatic transmissions. This type of master cylinder is of reduced length (88 mm compared to 138 mm for classic...

Replacing the brake booster
To check the performance of the brake booster: press the brake pedal several times with the engine off to create a uniform pressure in the vacuum booster cavities, close to atmospheric pressure; by the force applied to...

Replacing the front brake pads
Important! Be sure to replace all brake pads on the vehicle's axle, even if only one pad is worn. If you are reinstalling old brake pads, be sure to mark them before removing them. To remove the front brake pads: loosen...

Replacing the front brake caliper
To remove the front brake caliper: loosen the front wheel mounting bolts, raise the front of the car and secure it on stands. Unscrew the mounting bolts and remove the wheel; remove the front brake pads; remove the cap...

Replacing rear brake pads
To remove the rear brake pads: loosen the rear wheel mounting bolts, then raise the rear of the car and secure it on stands. Unscrew the mounting bolts and remove the wheel; remove the cap from the brake fluid expansion...

Replacing the rear brake caliper
To remove the rear brake caliper: release the parking brake lever; loosen the rear wheel mounting bolts, raise the rear of the car and secure it on stands. Unscrew the mounting bolts and remove the wheel; remove the...

Replacing the brake disc
To remove the brake disc: loosen the wheel mounting bolts, lift the corresponding part of the car and secure it on stands; remove the wheel; remove the brake pads; slowly rotate the brake disc so that it can be viewed...

Replacing the brake light switch
To remove the brake light switch: Figure 8.17. Location of the electrical connector (1) of the brake light switch disconnect electrical connector 1 (figure 8.17) from the brake light switch; Note: The brake light switch...

Adjusting the parking brake
Figure 8.18. Parking brake components: A - floor mounting area; B - fastening clamps on the body The location of the parking brake components is shown in the figure 8.18. To check the parking brake: raise the car by...

Replacing brake fluid
Brake fluid should not come into contact with mineral oils. Even a small amount of mineral oil makes the brake fluid unsuitable for use in the brake system. Replace the brake fluid for each branch of the hydraulic...

Bleeding air from the hydraulic brake system
Bleeding the hydraulic brake system is necessary to remove air, which significantly reduces braking efficiency. Air can enter the hydraulic drive due to depressurization of the system during repairs, replacement of...

Diagnostics of the EVA BOSCH system
Preliminary diagnostics of additional assistance during emergency braking can be carried out independently without the use of special equipment. The degree of assistance during emergency braking increases when the speed...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

See similar information for other Peugeot models

➨ Chassis, running gear: Brake system Peugeot 106 (1991-2003)
➨ Chassis, running gear: Brake system Peugeot 207 (2006-2014)
➨ Chassis, running gear: Brake system Peugeot 406 (1995-2004)
➨ Chassis, running gear: Brake system Peugeot 605 (1989-2000)
➨ Chassis, running gear: Brake system Peugeot 806 (1994-2002)

Link to this section in different formats

TEXTHTMLBB Code